### Determine the shear stresses at each of the following points

Assignment Help Civil Engineering
##### Reference no: EM13544605

A 6 inch X 4 inch rectangular beam is subjected to a maximum shear force of 1900 lbf. Determine the shear stresses at each of the following points on the beam cross section:

(a) a point on the top surface of the beam (and thus the top edge)

(b) a point 2 inches above the neutral plane of the beam

(c) a point on the neutral plane of the beam

Please show all steps and work.

#### Questions Cloud

 Find the normal and shear stresses on an oblique plane whose : At a point in a material, a resultant stress of 151 MN/m^2 acts in a direction making angles of 52 deg, 79 deg, and 40.13 deg with the coordinate axes, x,y and z respectively What statement best describes how a static system differs : The coordinates for the benchmark are 1421334.93,783207.62 the first point in the survey for oleson village, is 113.66 feet from the benchmark and at a bearing of n5d27'23"w. this is other survey point 542.16 So how dose this work? Describe how the following ratios and indices are used : A breif explination on clay mineralogy including isomorphous substitution, specific surface, cation exchange capacity and their effect on clay properties. Determine the maximum flexural stress due to two concentrate : If the performance of an entire system, due to the actions and interactions of its component subsystems, is measured as being greater than the sum of the performance of the individual subsystems' actions if they operated independently then we have ob.. Determine the shear stresses at each of the following points : A 6 inch X 4 inch rectangular beam is subjected to a maximum shear force of 1900 lbf. Determine the shear stresses at each of the following points on the beam cross section: Determine the allowable moment about the horizontal neutral : Determine the allowable moment about the horizontal neutral axis that a timber beam with nominal size 50 X 100 can resist without exceeding the allowable stress of 10 MPa. The dressed size is 38.1 X 88.9 mm, I = 0.00000223m^4, and S = 0.0000502 m^3. What is the maximum that each of these 2 equal loads can be : A 100 mm diameter log is subjected to two equal loads equally spaced along its 450 mm length at 150mm intervals. The beam has an allowable flexural stress of 9 MPa and a much lower allowable shear stress parallel to the grain of 850 kPa What other structural considerations are necessary in the : If the maximum allowable compressive stress of timber is 7MPa, what is the minimum available size of square section post required. (give dimensions as well as area). Please show working. Determine the minimum size of the pad footing for a steel : A geotechnical report has suggested an allowable bearing pressure of 200kPa. Determine the minimum size of the pad footing for a steel column if a factor of safety of 2.0 is recommended (include an estimate of self weight of the footing in your calcu..

### Write a Review

#### Moles of gas in the gas sample

A gas occupise 250 ml and it's pressure is 550mm Hg @ 254C how many moles of gas are in this sample? (convert mm Hg to atm).

#### Estimate the aqueous concentration of pce in water

Consider tetrachloroethene (PCE) in water. The vapor pressure of PCE is 0.0251atm. Henry's constant for PCE at 25°C is 26.9 atm-L/mol. Estimate the aqueous concentration of PCE in water at equilibrium

#### When will the loan be paid off

A person applied a mortgage of \$300,000.A mortgage company claimed the interest rate for the 15-year loanis 6.5%. (a) What would be the monthly payment? (b) If the personaccepted the terms of the loan on Oct.

#### How much will each leg shorten under the applied

given that E for the tube material is 70 GN/m2 and the stool legs are 75cm long, how much will each leg shorten under the applied compressive load (take g = 9.8m/s2)

#### Probability of pulling out vehicle at oncoming traffic

Assuming a standard driver reaction time of 2.5 seconds, what is the probability that the vehicle pulling out will get in an accident with oncoming traffic?

#### Design and detail the steel reinforcement for the section

The beam has a rectangular section which is to be singly reinforced. Given pt=1.1% design and detail the steel reinforcement for the section where the moment is maximum

#### What amount of depreciation will you claim for each calender

What amount of depreciation will you claim for each calenderyear during the period 1972-1975?

#### What is the chlorine concentration when the tank is put back

A water tower containing 4000 m3 of water has been taken out of service to install a chlorine monitor. The concentration of chlorine in the water tower was 2.0 mg/L when the tower was taken out of service.

#### Find specific weight and total moisture content of sample

A sample of dry sand with a specific gravity total of 16.49 kN/m3 and a relative density of 2.67 grains, is placed outdoors. During a rainy period, the sample volume remains constant but the degree of saturation increases to 40%.

#### Estimate the coefficient of permeability for a uniform sand

A grain-size analysis for a uniform sand in a loose state indicated that the soil particle diameter corresponding to 10% passing on the grain-size distribution curve is 0.18 mm. Estimate the coefficient of permeability.

#### What maximum load can be applied tot the center of the beam

A simply supported steel 'I beam' is made of three 1"*8" plates with a mass of 898.4 lbmass each as shown in I beam form. Steel has a modulus of elasticity of 30*10^6 psi. The beam is allowed to deflect 1.05 inch.

#### Determine the trade off between the cost and the head loss

The headloss per meter for galvanized iron pipe (.02 m diameter) hL= 0.110m and for (0.15m diameter) hL= 0.490m. Determine the trade off between the cost and the head loss (hL).

#### Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!