What statement best describes how a static system differs

Assignment Help Civil Engineering
Reference no: EM13544608

(a) System models are used to assist in understanding an actual system and we usually develop and use models that are exact representations of the actual system.

1-True

2-False

(b) What statement best describes how a static system differs from a dynamic system?

1. A static system's characteristics are fixed regardless of the state of any external factors in its environment.

2. A static system always exhibits a linear relationship between its inputs and its outputs.

3. Static systems are the most common system type used to model complex systems.

4. All of the answer options listed here.

(c)Ludwig von Bertalanffy was a:

1. dutch economist in the 18th century.

2. a civil engineer in the 1900's who worked closely with Brunel.

3. biologist in the 20th century.

4. German mathematician in the 20th century.

(d)The coordinates for the benchmark are 1421334.93,783207.62 the first point in the survey for oleson village, is 113.66 feet from the benchmark and at a bearing of n5d27'23"w. this is other survey point 542.16 So how dose this work?

Reference no: EM13544608

Questions Cloud

Determine the dynamic viscosity of glycerin at 85 degrees : Two parallel plates, one moving at 4m/s and the other fixed, are seperated by a 5mm thick layer of oil of specific gravity 0.80 and kinematic viscocity 1.25 X 10^-4 m2/s. What is the average shear stress in the oil?
Classify the soils using the given grain size distribution : Classify the following soils using the given grain size distribution (ASTM system) and Atterberg Limits data:
Compute the circumferential stress to which the wall : The length of a reading room in a library is 10 m and its breadth is 8 m. Compute the distributed live load, assuming the basic value of the load to be 2873 N/m2.
Find the normal and shear stresses on an oblique plane whose : At a point in a material, a resultant stress of 151 MN/m^2 acts in a direction making angles of 52 deg, 79 deg, and 40.13 deg with the coordinate axes, x,y and z respectively
What statement best describes how a static system differs : The coordinates for the benchmark are 1421334.93,783207.62 the first point in the survey for oleson village, is 113.66 feet from the benchmark and at a bearing of n5d27'23"w. this is other survey point 542.16 So how dose this work?
Describe how the following ratios and indices are used : A breif explination on clay mineralogy including isomorphous substitution, specific surface, cation exchange capacity and their effect on clay properties.
Determine the maximum flexural stress due to two concentrate : If the performance of an entire system, due to the actions and interactions of its component subsystems, is measured as being greater than the sum of the performance of the individual subsystems' actions if they operated independently then we have ob..
Determine the shear stresses at each of the following points : A 6 inch X 4 inch rectangular beam is subjected to a maximum shear force of 1900 lbf. Determine the shear stresses at each of the following points on the beam cross section:
Determine the allowable moment about the horizontal neutral : Determine the allowable moment about the horizontal neutral axis that a timber beam with nominal size 50 X 100 can resist without exceeding the allowable stress of 10 MPa. The dressed size is 38.1 X 88.9 mm, I = 0.00000223m^4, and S = 0.0000502 m^3.

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  How to determine the diameter of a drilled shaft pile

Using 1630.56 kN as the ultimate capacity determine the diameter of a drilled shaft pile that would have the same ultimate capacity and depth embedment (11.5 m) using the FHWA method. Neglect shaft resistance. Use a F.S. of 2

  Determine force exerts on the path when arrives at point a

A 2-kg block slides on the smooth circular path (Quadrant One of full circle, block moving left to right). If it is released from rest when theta=0 degrees, determine the force it exerts on the path when it arrives at Point A

  Estimate what is the critical slope of the channel

A trapezoidal channel cut into rock has a bottom width of 4 ft, side slopes of 1:1 and a channel slope of 0.0005. What is the critical slope of the channel.

  Calculate the uniform flow depth in the channel at flow rate

Water flows i a 8-m-wide rectangular channel that has longitudinal slope of .0001. The channel has an equivalent sand roughness of 2mm. Calculate the uniform flow depth in the channel when the flow rate is 15m^3/s. Use the Darcey-Weisbach equation..

  Determine the stack-gas so2 concentration in units

The sulfur dioxide (SO2) stack-gas concentration from fossi-fuel combustion is 2 ppmv. Determine the stack-gas SO2 concentration in units of micro grams/m^3. Assume 0C and 1 atm pressure

  Determine what should be the magnitude of the load p2

A second load P2 is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the post are dAB= 1.25 in, tAB= 0.5 in, dBC= 2.25 in and tBC= .375 in respectively.

  Determine the flow rate per unit width of aquifer

The aquifer is inhomogeneous with K = 12+0.006x, where x =0 at point 1, and the piezometric heads at point 1 and 2 are 14.2 m and 18.8 m, respectively measured above the upper confining layer.

  Develop and equation that defines the concentration

A first order reaction takes place in a batch reactor to remove an undesired contaminant (compound A) from a drinking water. The rate constant = 2.0 per day.

  Determine which should be the tangent function

in the first couple steps you are using the sine function to derive that the interior triange BCG is a right triangle. However, the sine function, by definition, is opposite divided by hypotenuse.

  Find how many dimensionless parameters govern this problem

The flowrate Q over a rectangular sharp crested weir depends on the width of the notch b, the head on the weir H, and the acceleration due to gravity g.

  Determine correct horizontal distance considering a slope

A civil engineer used a 30-m tape in measuring an inclined distance. The measured length on the slope was recorded to be 459.20 m long. The difference in elevation between the initial and the end point was found to be 1.25 m.

  A lower tank contains water while an upper tank contains

a lower tank contains water while an upper tank contains air with a negligible concentration of water vapor. a tube

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd