Determine the minimum size of the pad footing for a steel

Assignment Help Civil Engineering
Reference no: EM13544601

A geotechnical report has suggested an allowable bearing pressure of 200kPa. Determine the minimum size of the pad footing for a steel column if a factor of safety of 2.0 is recommended (include an estimate of self weight of the footing in your calculations). The total load of the column is 447.644kN

Reference no: EM13544601

Questions Cloud

Determine the shear stresses at each of the following points : A 6 inch X 4 inch rectangular beam is subjected to a maximum shear force of 1900 lbf. Determine the shear stresses at each of the following points on the beam cross section:
Determine the allowable moment about the horizontal neutral : Determine the allowable moment about the horizontal neutral axis that a timber beam with nominal size 50 X 100 can resist without exceeding the allowable stress of 10 MPa. The dressed size is 38.1 X 88.9 mm, I = 0.00000223m^4, and S = 0.0000502 m^3.
What is the maximum that each of these 2 equal loads can be : A 100 mm diameter log is subjected to two equal loads equally spaced along its 450 mm length at 150mm intervals. The beam has an allowable flexural stress of 9 MPa and a much lower allowable shear stress parallel to the grain of 850 kPa
What other structural considerations are necessary in the : If the maximum allowable compressive stress of timber is 7MPa, what is the minimum available size of square section post required. (give dimensions as well as area). Please show working.
Determine the minimum size of the pad footing for a steel : A geotechnical report has suggested an allowable bearing pressure of 200kPa. Determine the minimum size of the pad footing for a steel column if a factor of safety of 2.0 is recommended (include an estimate of self weight of the footing in your calcu..
General systems theory encourages us to use a holistic : The evaluation of various possible scenarios (either future or past) using simulation models can be tremendously valuable as a tool used in strategic plan development.
Why you think the actual volume pumped in a real clean : A cylindrical volume of soil contaminated with trichloroethylene (TCE). It is about 2.5 m deep and about 4.0 m in diameter. The porosity of the soil is approximately 0.25.
Estimate the time between when the concentration ratios : A conservative tracer is applied to the ground surface and leached through the vadose zone by rainfall. The average volumetric water content is 0.40 over the upper 4 meters and 0.30 over the remaining 3 meters above the water table
Compute the required weight of coarse aggregate per cubic : A concrete mix with a 3-inch slump, w/c ratio of 0.50 and a sand with a fine modulus of 2.4 contains 1700 lb/cubic yard of coarse aggregate. Compute the required weight of coarse aggregate per cubic yard.

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Determine the shear force and bending moment diagrams

a 200 lb divers stands on the end of the diving board. determine the shear force and bending moment diagrams

  Design and detail the steel reinforcement for the section

The beam has a rectangular section which is to be singly reinforced. Given pt=1.1% design and detail the steel reinforcement for the section where the moment is maximum

  Calculate the pressure at the bottom of the test tube

An open test tube at 293 K is filled at the bottom with 12.1 cm of Hg and 5.6 cm of water is placed above the mercury. Calculate the pressure at the bottom of the test tube if the atmospheric pressure is 756 mm Hg.

  Determine the pressure variation in the flow field

A plane flow field is developed by addition of a free vortex and a uniform stream in the positive x direction. If the vortex is located a distance a from the origin, find the pressure variation in the flow field.

  Create visual window-based program for multiplying two num

create a visual, window-based program for multiplying two 3x3 matrices together. Create 18 text boxes for input and 9 text boxes or labels for output

  Calculate the factor of safety and deformation

A 1 cm diameter, 0.4 m long steel rod is to be used in an application where it will be subjected to an axial tensile force of 15kN. The factor of safety based on yield stress must be at least 1.5, and the axial deformation must not exceed 2 cm.

  What will be the concentration of tce in the aqueous phase

The dimensionless henry's constant for TCE at 25 degrees celsius is 0.4. A sealed glass vial is prepared that has an air volum of 4mL overlying an aquesous volume of 36mL.

  Find the capacity of the column with reingforcement

A circulatr concrete column with a diameter of 8" has spiral reinforcing. Find the capacity of the column with 1% reingforcement. Find the capacity of the column with 8% reinforcement.

  Conclude that the mean cost of the new method is less

It is thought that a new process for producing a certain chemical may be cheaper than the currently used process. Each process was run 6 times, and the cost of producing 100-L of the chemical was determined each time.

  Determine what is the percent volatile matter in the sample

A suspended solids analysis is run on a sample. The tare mass of the crucible and filter is 55.3520 g. A sample of 260 mL is then filtered and the residue dried to constant mass at 103 degrees C.

  What temperature change is required to return the specimen

The elastic modulus is 40 GPa, the yield stress is 150 MPa, the ultimate stress is 525 MPa, and the ultimate strain is 0.38 (mm/mm). Perform the following tasks for this material.  compute the tangent modulus between yield stress and ultimate stres..

  How long must diameter be for mallet to balance at a point 6

A wood mallet has a cylindrical head 6 inches long and 3 inches in diameter. If the cylindrical head is 1 inch in diameter how long must it be for the mallet to balance at a point 6 inches from where the handle enters the mallet

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd