What is the maximum that each of these 2 equal loads can be

Assignment Help Civil Engineering
Reference no: EM13544603

A 100 mm diameter log is subjected to two equal loads equally spaced along its 450 mm length at 150mm intervals. The beam has an allowable flexural stress of 9 MPa and a much lower allowable shear stress parallel to the grain of 850 kPa. What is the maximum that each of these 2 equal loads can be? Which case is limiting for this beam?

Please show all steps and work.

Reference no: EM13544603

Questions Cloud

Describe how the following ratios and indices are used : A breif explination on clay mineralogy including isomorphous substitution, specific surface, cation exchange capacity and their effect on clay properties.
Determine the maximum flexural stress due to two concentrate : If the performance of an entire system, due to the actions and interactions of its component subsystems, is measured as being greater than the sum of the performance of the individual subsystems' actions if they operated independently then we have ob..
Determine the shear stresses at each of the following points : A 6 inch X 4 inch rectangular beam is subjected to a maximum shear force of 1900 lbf. Determine the shear stresses at each of the following points on the beam cross section:
Determine the allowable moment about the horizontal neutral : Determine the allowable moment about the horizontal neutral axis that a timber beam with nominal size 50 X 100 can resist without exceeding the allowable stress of 10 MPa. The dressed size is 38.1 X 88.9 mm, I = 0.00000223m^4, and S = 0.0000502 m^3.
What is the maximum that each of these 2 equal loads can be : A 100 mm diameter log is subjected to two equal loads equally spaced along its 450 mm length at 150mm intervals. The beam has an allowable flexural stress of 9 MPa and a much lower allowable shear stress parallel to the grain of 850 kPa
What other structural considerations are necessary in the : If the maximum allowable compressive stress of timber is 7MPa, what is the minimum available size of square section post required. (give dimensions as well as area). Please show working.
Determine the minimum size of the pad footing for a steel : A geotechnical report has suggested an allowable bearing pressure of 200kPa. Determine the minimum size of the pad footing for a steel column if a factor of safety of 2.0 is recommended (include an estimate of self weight of the footing in your calcu..
General systems theory encourages us to use a holistic : The evaluation of various possible scenarios (either future or past) using simulation models can be tremendously valuable as a tool used in strategic plan development.
Why you think the actual volume pumped in a real clean : A cylindrical volume of soil contaminated with trichloroethylene (TCE). It is about 2.5 m deep and about 4.0 m in diameter. The porosity of the soil is approximately 0.25.

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Write 2 user-defined functions for water volume to decrease

Using estimates of rainfall, evaporation, and water consumption, the town engineer developed the following model of the water volume in the reservoir as a function of time

  Determine the maximum allowable axial tensile force

A 4-cm- diameter rod of aluminum 7075-T6 is to subjected to an axial tensile force such that the factor of safety based on the yield stress on 1.75. Find the maximum allowable tensile force.

  A mechanic uses a crowfoot wrench to loosen a bolt at c the

a mechanic uses a crowfoot wrench to loosen a bolt at c. the mechanic holds the socket wrench handle at points a and b

  Compute the energy loss in a 90 degree bend in a steel tube

Compute the energy loss in a 90 degree bend in a steel tube used for a fluid power system. The tube has a 0.5 inch outside diameter and a wall thickness of 0.065 inches. The mean bend radius is 2.00 in. The flow rate of hydraulic oil is 3.5 gal/mi..

  Determine how high was the buckle into an isosceles triangle

They completed the installation when the temperature was 20 degrees Celsius. When the temperature rose to 25 degrees Celsius, the rail buckled into an isosceles triangle because they had not left an expansion gap.

  Determine the required do concentration in the treatment

Given the following information, determine the required DO concentration in the treatment plant effluent discharge in order to ensure that at no point downstream the DO in the river drops below 4 mg/L:

  Find require diameter of bar according to max stress critera

A bar with a circular cross-sectional area is made of SAE 1045 carbon steel having a yield stress of sY = 1000 MPa. The bar is subjected to a torque T=3.75 kNm and a bending moment M=7 kNm. Using a factor of safety FS=2 with respect to yielding

  What would the new value of hc be

If the fracture were planar in shape, having an average opening of 2 mm, what would the new value of Hc be?

  Explain what design speed was used to design the curve

A freeway exit ramp has a single lane and consists entirely of a horizontal curve with a central angle of 90 degrees and a length of 628 ft. If the distance cleared from the centerline for sight distance is 19.4 ft

  Question in structure analysis concrete column with

question in structure analysis concrete column with dimension square 300 mm300 mm length 3m and concrete grade c3545.

  Indicate a maximum rate of climb and rate of descent

1.Remain at the previously indicated rate of climb 2.Fall to zero rate of climb indication 3.Indicate a maximum rate of climb 4.Indicate a maximum rate of descent

  Latent heat of fusion problem

What mass (in grams) of steam at 100°C must be mixed with 387 g of ice at its melting point, in a thermally insulated container, to produce liquid water at 26.0°C? The specific heat of water is 4186 J/kg·K. The latent heat of fusion is 333 kJ/kg, ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd