What other structural considerations are necessary in the

Assignment Help Civil Engineering
Reference no: EM13544602

A timber post in a domestic dwelling is subject to an axial load of 64kN under the worst load case.

part(a) If the maximum allowable compressive stress of timber is 7MPa, what is the minimum available size of square section post required. (give dimensions as well as area). Please show working.

part(b) The post is 5.3m high, carrying loads from a second storey attic as well as roof loads down to the foundations. Apart from axial load capacity, what other structural considerations are necessary in the design of the member. Plaese explain

Reference no: EM13544602

Questions Cloud

Determine the maximum flexural stress due to two concentrate : If the performance of an entire system, due to the actions and interactions of its component subsystems, is measured as being greater than the sum of the performance of the individual subsystems' actions if they operated independently then we have ob..
Determine the shear stresses at each of the following points : A 6 inch X 4 inch rectangular beam is subjected to a maximum shear force of 1900 lbf. Determine the shear stresses at each of the following points on the beam cross section:
Determine the allowable moment about the horizontal neutral : Determine the allowable moment about the horizontal neutral axis that a timber beam with nominal size 50 X 100 can resist without exceeding the allowable stress of 10 MPa. The dressed size is 38.1 X 88.9 mm, I = 0.00000223m^4, and S = 0.0000502 m^3.
What is the maximum that each of these 2 equal loads can be : A 100 mm diameter log is subjected to two equal loads equally spaced along its 450 mm length at 150mm intervals. The beam has an allowable flexural stress of 9 MPa and a much lower allowable shear stress parallel to the grain of 850 kPa
What other structural considerations are necessary in the : If the maximum allowable compressive stress of timber is 7MPa, what is the minimum available size of square section post required. (give dimensions as well as area). Please show working.
Determine the minimum size of the pad footing for a steel : A geotechnical report has suggested an allowable bearing pressure of 200kPa. Determine the minimum size of the pad footing for a steel column if a factor of safety of 2.0 is recommended (include an estimate of self weight of the footing in your calcu..
General systems theory encourages us to use a holistic : The evaluation of various possible scenarios (either future or past) using simulation models can be tremendously valuable as a tool used in strategic plan development.
Why you think the actual volume pumped in a real clean : A cylindrical volume of soil contaminated with trichloroethylene (TCE). It is about 2.5 m deep and about 4.0 m in diameter. The porosity of the soil is approximately 0.25.
Estimate the time between when the concentration ratios : A conservative tracer is applied to the ground surface and leached through the vadose zone by rainfall. The average volumetric water content is 0.40 over the upper 4 meters and 0.30 over the remaining 3 meters above the water table

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Design a suitable pavement consisting of a granular subbase

if the subgrade has a resilient modulus of 103,500kN/m2, design a suitable pavement consisting of a granular subbase with a layer of coefficient of 0.13, a granular base layer with a layer coefficient of 0.14, and an asphalt concrete surface with ..

  Draw the influence line for the shear at point b

Draw the influence line for the shear at point B. Plot numerical values every 5 ft. Assume the support at A is a roller and C is fixed. EI is constant.

  A rectangular clarifier with a lengthwidth ratio of 31

a rectangular clarifier with a lengthwidth ratio of 31 receives a flow of 850m3day. the clarifiers depth is 4.0m and

  Compute the effective normal stress acting on a plane

The water table is at a depth of 1 m. Compute the effective normal stress and the shear stress acting on a plane rotated 60 degrees clockwise from the horizontal at a depth of 2.5 m in this deposit.

  Calculate total co2 emissions from two polices from 2011

A more conservative increase from 27.5 mpg in 2011 to 35 mpg by 2020 is supported widely in Washington. California and 13 other states + the District of Columbia hope to increase that stander to 35 mpg by 2017 and 40 mpg by 2020.

  Estimate the evaporation volume for the month in m3

Lake Mead has a water surface area of 65,800 hectares. In acertain month the reservoir is full, and the pan evaporation rateis 25 cm. Using a pan coefficient of 0.73, estimate theevaporation volume for the month in m3.

  How might the absence of intrinsic factor affect the bones

Intrinsic factor, which is made by the stomach, must be present forthe body to absorb Vitamin B12 How might the absence of intrinsic factor affect the bones of a patient?

  Determine the angular velocity of pinion gear and velocity

The pinion gear rolls on the gear racks. If B is moving to the right at 8 ft/s and C is moving to the left at 4 ft/s, determine the angular velocity of the pinion gear and velocity of its center A.

  The heated water outflow from a nuclear power plant

The heated water outflow from a nuclear power plant is cooled in a 50-m wide rectangular channel that has a discharge, Q = 225.0 m3/s. The Manning’s n is 0.015 and the bed slope is 5.0x10-4

  Calculate the coefficient of volume compressibility

In an oedometer test, the void ratio of a clay sample changed from 1.62 to 1.41 as the vertical effective stress imposed on the sample was increased from 100 kPa to 200 kPa.

  What is the height of the lighthouse above sea level

An observer standing on a beach can just see the top of a lighthouse 15 miles away. The eye height of the observer abouve sea level is 5.7 feet. what is the height of the lighthouse above sea level

  Determine the seepage velocity-v through the sample

The cross-sectional area of the sample was 60 cm2 and its length was 150 mm. For 80 cm3/min steady-state flow rate, a total head difference of 8 cm was measured across two points separated by 10 cm along the axis of the sample.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd