What maximum force can this person apply with this jack

Assignment Help Civil Engineering
Reference no: EM13557085

a) A container of petrol on a set of scales is used to measure the rate at which fuel is used by an engine under test. In one test the weight measured by the scales decreases by 25.0 N in 1 hour. (Assume the specific gravity of petrol is 0.720 and g is 9.81 m/s^2)

What is the rate (in L/s) of fuel used by the engine in this test

b) The undercarriage for an aircraft uses two springs between each wheel and the aircraft fueselage to cuhion the landing of the aircraft. There are two sprung wheels and the mass of the aircraft is 5000kg

Assuming a worst case scenario of a 0.20m drop of the full mass of the aircraft, what is the expected compression (in metres) of the 4 springs, if the spring constant K = 4000/Ncm

(Assume g is 9.81 m/s^2)

c) A person of mass 80kg places all their weight on the pedal of a foot operated hydraulic jack. The diameter of the hydraulic cylinder under foot pedal is 4cm and the diameter of the jack cyclinder is 9cm (Assume g is 9.81 m/s^2)

What maximum force can this person apply with this jack. Show your working

Reference no: EM13557085

Questions Cloud

Determine the rate of heat exchange between the human : A human with a surface area of 2 m^2 and a surface temperature of 27 degrees celcius radiates into a large room (which acts as a black body),
What is the exit state of the water : Water flows through a tube at a rate of 7.5 kg/min while heat is added to it at a rate of 4.5 kW. If water entered at 20 degrees celcius, determine the exit temperature. Assume the pressure remains constant at 1 atm throughout.
Estimate the standard deviation of the population : A sample of 10 television tubes produced by a company showed a mean lifetime of 1200 hours and a standard deviation of 100 hours. Estimate
Constuct a choice table for interest rate from 0% to 100% : The owner of a downtown parking lot has employed a civil engineering consulting frim to advise him on the economic feasibility of constructing an office building on the site. bill samuels, a newly hired civil engineer, has been assigned to make the a..
What maximum force can this person apply with this jack : A container of petrol on a set of scales is used to measure the rate at which fuel is used by an engine under test. In one test the weight measured by the scales decreases by 25.0 N in 1 hour. (Assume the specific gravity of petrol is 0.720 and g is ..
What is its speed at the point that the force resisting : This problem models an insertion process. Block A (mA = 2kg) is acted on by a horizontal force F (F = 12 N). As A moves to the right, it gets pressed more and more tightly in the channel.
How long will it take for the pce to reach the well : The water is pumped out of the aquifer at a rate of 2000 gpd, treat it with activated carbon and then put it back into the aquifer. At the flow rate how long until al the PCE is removed, assume carbon removed 100% of the PCE (ans. 54 days)
How long will it take the water in the aquifer to travel : A truck spils 1 gallon of benzene into an aquifer with an area= 50ft^2 Benzene has a solubility of 1750 ppm, and a specific gravity of 0.873. The aquifer ahs a porosity of 0.25, a hydraulic gradient of 0.004 and a hydraulic conductivity of 1000 gpd/f..
Determine the speed of the arrow after traveling from rest : A bowstring produces a force against a 2.0 oz arrow given by where a = 40 lbf, b = 3.2 ft-1 and x is in ft. x = 0 when the arrow is pulled fully back and increases as the arrow moves forward. Determine the speed of the arrow after traveling from rest..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the torque and bending moment

Four strain gages are mounted at 90o intervals around the circumference of a 100-mm steel shaft. E= 200 GPa, and ? = 0.3. All gages are oriented at an angle of 45o with respect to the longitudinal axis of the shaft.

  Pharmaceutical mixing tank

In year one, a pharmaceutical mixing tank had a market price of $120,000. It replaced an older smaller mixing tank that had a BV of $15,000.

  How long will it take to supply the required amount of drug

A catheter is a specialised needle intended for long-term insertion into a vein in a patient's arm. Engineers are redesigning them to cause less discomfort and damage. An intravenous chemotherapy system is based on a new catheter design.

  Determine the maximum allowed distributed force per length

The cable that supports the bar has an effective modulus and area of 14GPa and 77mm^2 , respectively. Let the lengths be 600mm and 300mm , and the angle 50 degrees . If the permitted additional elongation of the cable is 0.20mm

  Determine stress in member immediately after load is applied

You are analyzing a polymer uniaxial tension member used in a lightweight structure. The bottom of the tension member is fixed and the top has a tensile force F = 10,000 pounds on it.

  Determine the magnitude of the couple force on the crank

Determine the magnitude of the couple force so that the resultant couple moment on the crank is zero.

  Obtain the dimensionless groups that charactrize the problem

The power loss, p , in a journal bearing depends on length, L; diameter, D; clearance, c; and rotational speed, w. You also have to worry about lubricant viscosity, density, and pressure. Obtain the dimensionless groups that charactrize this probl..

  Calculate size of the critical radius and number of atoms

For maximum undercooling, calculate the size of the critical radius and the number of atoms in the critical nucleus when solid copper forms by nucleation.

  Define procedure of gauss-newton method used to control

explain in your words the procedure of the Gauss-Newton method used to control some parameter (z) to meet some expected performance (y) using controllable parameters (A,B)

  Determine the horizontal reaction

Determine the horizontal reaction that is developed on the gate at C.

  What will be the approximate temperature of the alloy

Is it possible to have a copper-silver alloy of composition 50 wt% Ag-50 wt% Cu that at equilibrium, consists of α and β phases having mass fractions Wα = 0.60 and Wβ=0.40

  A chemical engineer is considering two styles of pipes for

A chemical engineer is considering two styles of pipes for moving distillate from a refinery to the tank farm. A small pipeline will cost less to purchase (including valves and other appurtenances) but will have a high head loss and, therefore, a hig..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd