Estimate the standard deviation of the population

Assignment Help Civil Engineering
Reference no: EM13557087

A sample of 10 television tubes produced by a company showed a mean lifetime of 1200 hours and a standard deviation of 100 hours. Estimate

(a) the mean,

(b) the standard deviation of the population of all television tubes produced by this company.

How do we find the standard deviation. ?

Reference no: EM13557087

Questions Cloud

Figure out that the service time could be assumed : The chief engineer of an airport is planning to rehabilitate runway pavements over the next several months. You ask him what impact this would have on delays and queues, but he does not know
Determine the force p in the coupling between the trailer an : The hydraulic braking system for the truck and trailer is set to produce equal braking forces for the two units. If the brakes are applied uniformly for 5 sec to bring the rig to a stop from a speed of 20 mph while moving down a 10 percent grade
Determine the rate of heat exchange between the human : A human with a surface area of 2 m^2 and a surface temperature of 27 degrees celcius radiates into a large room (which acts as a black body),
What is the exit state of the water : Water flows through a tube at a rate of 7.5 kg/min while heat is added to it at a rate of 4.5 kW. If water entered at 20 degrees celcius, determine the exit temperature. Assume the pressure remains constant at 1 atm throughout.
Estimate the standard deviation of the population : A sample of 10 television tubes produced by a company showed a mean lifetime of 1200 hours and a standard deviation of 100 hours. Estimate
Constuct a choice table for interest rate from 0% to 100% : The owner of a downtown parking lot has employed a civil engineering consulting frim to advise him on the economic feasibility of constructing an office building on the site. bill samuels, a newly hired civil engineer, has been assigned to make the a..
What maximum force can this person apply with this jack : A container of petrol on a set of scales is used to measure the rate at which fuel is used by an engine under test. In one test the weight measured by the scales decreases by 25.0 N in 1 hour. (Assume the specific gravity of petrol is 0.720 and g is ..
What is its speed at the point that the force resisting : This problem models an insertion process. Block A (mA = 2kg) is acted on by a horizontal force F (F = 12 N). As A moves to the right, it gets pressed more and more tightly in the channel.
How long will it take for the pce to reach the well : The water is pumped out of the aquifer at a rate of 2000 gpd, treat it with activated carbon and then put it back into the aquifer. At the flow rate how long until al the PCE is removed, assume carbon removed 100% of the PCE (ans. 54 days)

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the magnitude of reaction

Determine the magnitude of reaction at point A (in kips) of a 20' beam with 5kips at 4' of the beam and 2kips at 9' of the beam at 350lbs./ft.

  Compute the normal depth with a bottom width

A trapezoidal channel with a bottom width of 4 feet and side slopes 2:1 (H:V) and a bed slope of 1 percent conveys a discharge of 50,000 gpm. Assume n = 0.025. Compute the normal depth

  How to determine span of the subject beam which theoretical

Again assuming d=14in, determine, or at least show exactly how to determine, the portion (length) of span of the subject beam which theoretically would require no shear reinforcement.

  Determine thenbspmagnitudes of the additional loads that

a concrete foundation mat in the shape of a regular hexagon ofnbspside 12 ft supports four column loads as shown.

  Calculate the vertical distance

A 600 ft vertical crest curve crosses a 4 ft diameter pipe at rightangles at station 110+85. The PVI of the vertical curve is station110+00 and elevation 1098.4 ft with an incoming tangent grade of1.2% and an outgoing tangent grade of -1.8%.

  Conclude that the mean cost of the new method is less

It is thought that a new process for producing a certain chemical may be cheaper than the currently used process. Each process was run 6 times, and the cost of producing 100-L of the chemical was determined each time.

  What is the mixed liquor suspended solids concentration

An activated sludge system treats 1500 m3/day of raw wastewater with a BOD of 250 mg/L. The reactor volume is 375 m3. The kinetic parameters were determined to be: x = 3 day-1, Y = 0.55 kg SS/kg cells, and Ks = 150 mg/L.

  Determine the rise in water level within the drainage layer

A rectangular landfill in the New England area is 175 m in width, and sloped at the uniform angle of 75 degrees. Its cover system includes a drainage layer constructed of clean, medium sand (Ks = 10^-2 cm/s).

  Determine what is the deflection at the center of the beam

A C10x20 catilever beam is 12 feet long, supported on the right side. The beam supports two point loads: Load 1 is 2500 lbf and is located 2.5 feet from the wall. Load 2 is 1300 lbf and is located 12 feet from the wall.

  What is the level of the service

If the peak-hour factor is .90 and all of the drivers are regular users, what is the level of the service of this compound-grade freeway segment?

  How much will be in a high-yield account at national bank

How much will be in a high-yield account at the National Bank of Arizona 12 years from now if you deposit $5000 now and $7000 fi ve years from now. The account earns interest at a rate of 8% per year, compounded quarterly

  Determine the normal and friction forces acting on each side

The photograph shows two U.S. Coast Guard icebreakers in an ice field, and a simple model for an ice breaking operation. If the coefficients of static and kinetic friction

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd