What is the required detention time and tank volume

Assignment Help Civil Engineering
Reference no: EM13536831

A chlorination process is to be used to disinfect a wastewater treatment plant effluent. The plant treats 1.8MGD (million gallon per day). The water entering this unit has about 4500mg/L of coliforms, and the effluent target is 0.1 mg/L of coliforms. The rate of disinfection can be described by dC/dt=-kC where C equals the concentration of coliforms. A laboratory study determined that the k=0.75min-1. If a plug flow reactor is used, what is the required detention time and tank volume to meet the effluent criteria? Show all work.

Reference no: EM13536831

Questions Cloud

Determine the rotation of the gear at e : The two shafts are made of A-36 steel. Each has a diameter of 25 mm and they are connected using the gears fixed to their ends. Their other ends are attached to fixed supports at A and B
What is the probability of a water shortage in this city : During the next month, the amount of water available for a city is lognormally distributed with a mean of 1 million gallons and a c.o.v. of 40%, where as the total demand is expected to follow a lognormal distribution with a mean of 1.5 million gallo..
Explain how these effects were initiated : Is it possible (in this part of the world) for the sun to ever shine directly upon the OUTSIDE of a NORTH-facing wall of a home or other building? If so when?
Determine the magnitude and the point of application the : Determine the magnitude and the point of application the resultant of the four wind forces (distance right of AB, and distance below BC) when a=1.5ft and b=13ft.
What is the required detention time and tank volume : A chlorination process is to be used to disinfect a wastewater treatment plant effluent. The plant treats 1.8MGD (million gallon per day). The water entering this unit has about 4500mg/L of coliforms, and the effluent target is 0.1 mg/L of coliforms.
How many pounds of sulphur would be emitted : Coal has about 5% sulfur. How many pounds of sulphur would be emitted from coal-fired power plants in the united states in 3 years? (each year. U.S electricity production in about 0.28 x 1012 watts, and coal has an energy content of about 30 x 106 J/..
What is the resulting solids concentration : Raw primary sludge at a solids concentration of 3% is mixed with waste activated sludge at a solids concentration of 6,000 ppm. The flows are 20 and 25 gal/min, respectively.
What is differential equation for beams subjected to axial : .An air turbine is used with a generator to generate electricity. Air at the turbine inlet is at 700 kPa and 25 degree C. The turbine discharges air in to the atmosphere at a temperature of 11 degree C.Inlet and outlet air velocities are 100 m/s and ..
What would the resulting lake concentration be and is this : A 10 X 106 m3 lake is fed by a polluted stream having a flow rate of 5 m3/s and a pollutant concentration of 10 mg/L. There is also a sewage outfall that discharges 0.5 m3/s of wastewater having a pollutant concentration of 100 mg/L. The stream and s..

Reviews

Write a Review

Civil Engineering Questions & Answers

  A ball is thrown with a velocity of 25ms at a building the

a ball is thrown with a velocity of 25ms at a building. the building is 20m high the man throwing the ball is 40m from

  Determine the normal strain in the two bars at 250 f

At a temperature of 60 F, a .04 in gap exists between the ends of the two bars. Bar 1 is an aluminum alloy [E=10,000ksi, v=.32, alpha=12.5x10^-6/F] bar with a width of 3 in and a thickness of .75 in.

  How to identify the sources of information presented at work

The knowledge of the geological and geotechnical characteristics of the subsoil is a basic step, fundamental to the development of any type of research, evaluation, study or project in the areas of Civil and Environmental Engineering.

  What are the best dimensions for a trapezoidal canal having

What are the best dimensions for a trapezoidal canal having a side slopes of 1V : 3H and n = 0.020, if it is to carry 40 m^3/s uniformly on a slope of 0.009.

  Differences in partitioning among several compartments

Can you explain the differences in partitioning among several compartments in terms of mass distribution and the compounds physical and chemical properties. For example, TCE mass distribution in air, water, soil, sediment, suspended solids and biota ..

  Determine the magnitude of the maximum shear stress

A torque of T = 3.00 kN-m will be applied to the hollow thin-walled aluminum alloy section. If the section has a uniform thickness of 4 mm, determine the magnitude of the maximum shear stress developed in the section.

  What is the new quality and pressure

Water at 120 0C with a quality of 25 % has itstemperature raised 20 0C in a constant volumeprocess. What is the new quality and pressure? Draw P-vand T-s diagrams

  Determine what must be the allowable elongation

A cylindrical rod of brass alloy (E = 100 GPa,) having a yield strength of 345 MPa is to be subjected to a load of 7500 N. If the length and diameter of the rod are 338 mm and 7.55 mm respectively, what must be the allowable elongation

  Determine the force p required to pull the shaft at velocity

A 25-mm diamenter shaft is pulled through a cylindrical bearing. The lubricant that fills the 0.3-mm gap between the shaft and bearing is an oil having a kinematic velocity of 8.0x10^-4 m^2/s and a specific gravity of 0.91.

  Determining axial load of a dense sand

A dense sand has an effective friction angle of 43 and c'=0. A dry, 2.8-inch diameter sample is tested in drained triaxial shear with a confining pressure of 2500 psf. What axial load, P (in pounds), will be required to fail the sample?

  Determine what is the largest circle that can be inscribed

What is the largest circle that can be inscribed within a polygon with corner coordinates (600,800), (900, 300), (500, 100), and (100, 40) Find the radius of the largest circle and show how you found it from these coordinates.

  Determine what is the maximum speed attainable by the car

A driver traveling on a roadway decides to overtake a slow-moving truck traveling at 15 mph. The accelerating characteristic of the car is given by the following: dv/dt= 2.08-0.032v where v is the speed (ft/sec), and t is the time (sec).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd