What is the conversion rate for parts per million by volume

Assignment Help Civil Engineering
Reference no: EM13534554

1.a)Find the change in currents due to change of voltage by (a)5mv, (b) -10mv, (c) 15mv using small signal model and exponentialmodel of diode with n= 1 and biased at 2mA.

b)A step up transformer has the turn ratio of2:5, find the secondary voltage of transformer ifprimary voltage given is 240 Vac.

2.What surveying observations does a contractor need to lay a 36 inch diameter pipe?

3.What is the conversion rate for parts per million by volume (ppmv)conversion. How is this converted into atm, Pa, and torr?

Reference no: EM13534554

Questions Cloud

Estimate the evaporation volume for the month : The pedestal supports a load P at its center. If the material has a mass density p, determine the radial dimension r as a function of z so that the average normal stress in the pedestal remains constant. The cross section is circular.
What is the mean annual volume of rainfalling on the water : The mean anual rainfall depth over a 280 km2watershed is 725 mm. What is the mean annual volume of rainfalling on the watershed in m3 ?
Calculate the corrected distance : When measuring a distance AB, the first taping pin was placed 1.5ft to the right of line AB and the second pin was set 1.5 ft leftof line AB. The recorded distance was 236.89 ft. ( Assume 3 tapedsegements, the first two 100 ft each.) Calculate the co..
What is the length of the core in inches if the diameter is : If the porosity of a core sample is 26 percent, the pore volume is7.7 cc, what is the length of the core in inchesif the diameter is 1.5 inches?
What is the conversion rate for parts per million by volume : What is the conversion rate for parts per million by volume (ppmv)conversion. How is this converted into atm, Pa, and torr?
Calculate specific surface : Immediately after the bouncing golf ball leaves the floor itscomponent of velocity are Vx= 0.662 m/s and Vy= 3.66 m/s. determinethe horizontal distance from the point where the bal
Is the fluid accelerating uphill : A fluid with a specific weight of 100lb/ft^3 and a negligibleviscous effects flows in a pipe. The pipe is inclined at 30degrees. Point (1) is located above point (2) in the pipe.
Show that 1 millimeter of the 0.02 n h2so4 solution : A load of 14 tonnes is suspended at the end of a steel rope.If the load is subjected to a maximum acceleration/deceleration of2.5m/s2, when raised and lowered, calculate the diameter of therope needed to support the load. Assume the following:
Compute the pressure at a point in a building : A rectangular culvert 4 feet x 6 feet is running full and discharging 3,500 cfm. There is no friction loss. Find the velocity in fps. The culvert empties into a 10 ft wide culvert and the velocity reduces to 0.6 fps. How deep is the water level in th..

Reviews

Write a Review

Civil Engineering Questions & Answers

  A vehicle pulls out onto a single lane highway that has a

a vehicle pulls out onto a single lane highway that has a flow rate of 280 vehhr poisson distributed. the driver of the

  Determine flow rate into or out of each reservoir

Three reservoirs are connected by three pipes with hA = 100 f t, hB = 20 f t, hC = 0 f t, l1 = 1000 f t, l2 = 500 f t, l3 = 400 f t and D1 = D2 = D3 = 1 f t. Determine flow rate into or out of each reservoir if friction in each pipe is 0.02.

  Calculate manning coefficient n for the given reach

The following data are obtained for a particular reach of the Provo river in Utah: cross sectional area A = 183 ft2, free surface width = 55 ft, average depth = 3.3 ft, Rh = 3.32 ft, V = 6.56 ft/s, length of the reach = 116 ft, and elevation drop ..

  Compute the specific weight and specific gravity of the oil

A pressure gage at elevation 4.8 m on the side of a storage tank containing oil reads 34.7 kPa.Another gage at elevation 2.2 m reads 57.5 kPa. Compute the specific weight, density, and specific gravity of the oil.

  Force that cause stress-free

The rigid bar abcd is supported by a pin at B and restrained by identical steel bars at C and D, each of area 250mm 2 . if the temperature is increased by 8 0 C, find out the force P that will cause the bar at c to be stress-free.

  At what load would you expect the specimen to fracture

Three-point bending test was performed on an aluminum oxide specimen having a circular cross section of radius 5.5 mm; the specimen fractured at a load of 850 N when the distance between the support points was 50 mm.

  Perform a check that the elevation of the curve at station

A vertical curve is to connect two tangents that intersect at station 30+50 at an elevation of 800.00 ft. The approach gradient is 3 percent and the departure gradient is -5 percent. The elevation of the curve at station 32+50 must be equal to at ..

  What is your recommendation for the maximum size of coarse

What is your recommendation for the maximum size of coarse aggregate for the following situation?

  What is work that must be done on the air in the cylinder

To provide a source of cooling on this hot Florida day, the piston is now pulled up until the air reaches a temperature of -100C. It can be assumed that the process is a polytropic one with.

  Determine the mean stream flow rate in ac-ft per year

Assume the 20 percent of the annual precipitation reaches the watershed outlet as stream flow. Determine the mean stream flow rate in ac-ft/yr, sfd/yr, and square meter/second

  Estimate the tensile strength and the modulus of elasticity

The concrete cylinder 6 in x 12 in broke incompression at a load of 110000 lbs. Compute the crushing strength of concrete. Estimate the tensile strength and the modulus of elasticity.

  How much will bar deform if it is released from the framwork

A 24-in.-long copper bar with a yield strength of 30,000 psi is heated to 120°C and immediately fastened securely to a rigid framework. The coefficient of thermal expansion for copper is 16.6x10-6 (1/oC).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd