Estimate the evaporation volume for the month

Assignment Help Civil Engineering
Reference no: EM13534558

1.Lake Mead has a water surface area of 65,800 hectares. In acertain month the reservoir is full, and the pan evaporation rateis 25 cm. Using a pan coefficient of 0.73, estimate the evaporation volume for the month in m 3.

2.The pedestal supports a load P at its center. If the material has a mass density p, determine the radial dimension r as a function of z so that the average normal stress in the pedestal remains constant. The cross section is circular.

3.Lines of levels were run requiring n instrument strips. Therod reading for each backsight and foresight has a standarddeviation σ. What is the standard deviation in the levelline?

n = 40 , σ = ±0.005

OK. This is what I did.

σ = ± 0.005√40 = ±0.032

Is this correct? If not please point in the right direction.

Reference no: EM13534558

Questions Cloud

Mitochondrium and chloroplast have number of similarities : The energy transfers taking place in the mitochondrium and the chloroplast have a number of similarities.  Briefly describe the basic process of transferring energy in the two organelles.  Include in the discussion the similarities between photosynth..
Include an appropriate synapomorph for each taxon : Draw a cladogram for the following taxa and include an appropriate synapomorph for each taxon. Agnatha, Arthropoda, Cephalopod, Chelicerata, Chordates, Chondrichthyes Gastropod, Gnathaostomes, Insects, Molluscs, Nematodes, Teleost
Krebs cycle is two carbon entering and two carbons leaving : While the standard view of the Krebs cycle is two carbon entering (acetyl CoA) and two carbons leaving (carbon dioxide) each round, other substrates enter and leave at different points as well.  What are the connecting pathways for each of the Kre..
What error results from curvature and refraction : A small plot of land has measured dimesnions of 50 by 150 ft. the incertianity in the 50-ft is +/- 0.01 ft. Calculate the uncertianity eith which the 150-ft must be measred to ensure that the total uncertainty is not greater than 150%.
Estimate the evaporation volume for the month : The pedestal supports a load P at its center. If the material has a mass density p, determine the radial dimension r as a function of z so that the average normal stress in the pedestal remains constant. The cross section is circular.
What is the mean annual volume of rainfalling on the water : The mean anual rainfall depth over a 280 km2watershed is 725 mm. What is the mean annual volume of rainfalling on the watershed in m3 ?
Calculate the corrected distance : When measuring a distance AB, the first taping pin was placed 1.5ft to the right of line AB and the second pin was set 1.5 ft leftof line AB. The recorded distance was 236.89 ft. ( Assume 3 tapedsegements, the first two 100 ft each.) Calculate the co..
What is the length of the core in inches if the diameter is : If the porosity of a core sample is 26 percent, the pore volume is7.7 cc, what is the length of the core in inchesif the diameter is 1.5 inches?
What is the conversion rate for parts per million by volume : What is the conversion rate for parts per million by volume (ppmv)conversion. How is this converted into atm, Pa, and torr?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Define water circulating through it at the rate

A 4 X 8-ft solar collector has water circulating through it at the rate of 1.0 gallon per minute while exposed to sunlight with intensity 300 Btu/ft^2-hr.

  Determine the minimum diameter a steel wire can have

If the elastic limit of steel is 5.0 10^8 Pa, determine the minimum diameter a steel wire can have if it is to support a 69-kg circus performer without its elastic limit being exceeded.

  What is the market value of the plants electricity annually

Biomass is increasingly used as a fuel to produce power and heat. A sugarcane-­? processing mill is powered by a biomass power plant with 140 MW of electricity and with 60 MW of heat in the form of steam for sugar extraction from the cane.

  What is the highest downward speed that jumper can attain

What is the highest downward speed (the terminal velocity), in miles per hour, ? At the terminal velocity the downward force (the weight) is equal to the upward force (the aerodynamic drag force).

  Explain how to calculate the mcl for the acceptable risk

the water is pumped out of the aquifer at a rate of 2000 gpd, treat it with activated carbon and then put it back into the aquifer. At the flow rate how long until al the PCE is removed, assume carbon removed 100% of the PCE

  How many watts of power would it take to heat 1 l of water

How many watts of power would it take to heat 1 L of water(weighing 1.0 kg) by 10 degrees Celsius n 1.0 h Assume no heat losses occur, so all of the energy expneded goes into heating the water.

  Determine the forces acting on the bracket at point c

The L bracket shown below is pinned to the ground at point C and attached to a single cable at points A and D that wraps around a frictionless pulley at point B. Determine the forces acting on the bracket at point C and then tension in the cable.

  What is the pressure difference in feet of water and in psi

Two vessels are connected to a differential manometer using mercury (s=13.56), the connecting tubing being filled with water. The higher-pressure vessel is 5 ft lower in elevation than the other

  Behaviour of structural material using comparative statement

The behaviour of structural materials using comparative statement when they are formed into structural member

  Determine x the downstream position of the pitot tube

Air at 20oC and 1atm flows at 20 m/s past the flat plate . A pitot tube placed 2mm from the wall, develops a manometer head h=16mm of Meriam red oil (SG = 0.827), measured relative to atmospheric pressure.

  Determine diameter of the shaft at allowable shear stress

The steel uniform shaft has four pulleys attached to it and frictionless bearings at its ends. The pulley at B is connected to a motor that is driving the system. The other three pulleys are consuming the power delivered by Pb .

  Determine crest height of suppressed weir that should be use

If the maximum (total) depth of water that can be accommodated at the weir is 1m and the width of the channel is 4m, determine the crest height of a suppressed weir that should be used to measure the flowrate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd