What is the area of one of these walls

Assignment Help Civil Engineering
Reference no: EM13534546

A new athletics stadium with a curved concrete roof is beingdesigned. Each of the end walls is 25 metres long. Its height ymetres is given by

y = 5 x1/2-x+3

where x is the horizontal distance in metres from the beginning ofthe wall.

What is the area of one of these walls (in m2)?

Reference no: EM13534546

Questions Cloud

Compute the pressure at a point in a building : A rectangular culvert 4 feet x 6 feet is running full and discharging 3,500 cfm. There is no friction loss. Find the velocity in fps. The culvert empties into a 10 ft wide culvert and the velocity reduces to 0.6 fps. How deep is the water level in th..
What is the meaning of most efficient crosssection : A rectangular channel has a bottomwidth = b and flow depth = y. Prove that for a given area, the mostefficient rectangular cross section is one with y = b/2.
What is the concentration in ppm at the downstream reach : Five million gallons per day (mgd) of a conservative substance,with concentration of 10 mg/L is released into a stream having anupstream flow of 10.0 mgd and a substance concentration of 3 mg/L.Assume complete mixing.
What is the true air speed : Given that an aircraft flying at FL350 encounters a tailwindof 35 knots and the instrument in the cockpit shows anindicated airspeed of 310 knots. What is the standard atmosphere atthis altitude?
What is the area of one of these walls : A new athletics stadium with a curved concrete roof is beingdesigned. Each of the end walls is 25 metres long. Its height ymetres is given by
What is the dimension of a strip footing : Based on given soil data. Soil is a loam with grain the #200sieve. The Liquid Limit = 29, Plastic Limit = 24, friction angleφ = 25 degree, cohesion c = 0.21 tons/sf, unit weight γ=124lb/ft3.
What is the pressure at the leading edge : When an airplane is flying 200mph at 5000-ft altitude in standardatmosphere, the air velocity at a certain point on the wing is 273mph relative to the airplane. What suction pressure is developed onthe wing at that point? What is the pressure at the ..
What weight can it bear before being broken : A concrete sidewalk slab is 17.5 MPa, 4 inches deep, and 2 m long.  A tree root has pushed it up so there is a 1 inch lip at the junction with the adjacent slab, and the slab is effectively 1 inch above its base underneath
Current magnetic bearing of the same line : Given an azimuth of 251 degrees 11' 23" for line ED. If theangle at DEO is 197 degrees 26' 12" measured clockwise, what is theazimuth and bearing of line EO?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the dimensions of the best cross section

Water is to be transported at a rate of 60,000 gallons/min in uniform flow in an open channel whose surface are lined with clay tile. The bottom slope is 0.0014. Determine the dimensions of the best cross section

  What weight can it bear before being broken

A concrete sidewalk slab is 17.5 MPa, 4 inches deep, and 2 m long.  A tree root has pushed it up so there is a 1 inch lip at the junction with the adjacent slab, and the slab is effectively 1 inch above its base underneath

  Calculate the maximum design load on a hollow aisi

Calculate the (maximum) design load on a hollow AISI 1020 steel shaft with an outside diameter of 2.5 inches and an inside diameter of 2 inches. Assume a safety factor of 2.

  Determine void ratio and unit dry weight of soil particles

A 110 cm^3 sample of wet soil has a mass of 106 g and a degree saturation of 100%. When oven-dried, the mass is 81 g. Determine the 1) water content, 2) specific gravity, 3) void ratio, and unit dry weight of soil particles.

  What would be the reading on a barometer containing benzene

What would be the reading on a barometer containing Benzene at 20 degrees Celsius at a time when the atmospheric pressure was equivalent to 12.3 m of water

  Determine the dead uniform load in kips per linear foot

A wide flange steel beam supports a permanent concrete masonry wall, floor slab; architectural finishes mechanical and electrical systems. Determine the dead uniform load in kips per linear foot acting on the beam.

  Determine the greatest weight of the machine that the beam

The beam has a flange width b=8 in. If the maximum bending stress is not to exceed σallow=22 ksi, determine thegreatest weight of the machine that the beam can support. The center of gravity for the machine is at G, and the supports at Band C are smo..

  A soil sample has the following data

A soil sample has a wet unit weight of 96 lb/ft^3, amoisture content of 17% and a degree of saturation of 60%. Findthe: (A) Void Ratio, (B) Specific gravity, (C) Saturated unitweight.

  What are the recorded values of r dot and r double dot

at the bottom of a loop in the vertical plane an airplane has a horizontal velocity of 315 mi/h and is speeding up at a rate of of 10ft/s^2. The radius of curvature of the loop is 1mi. The plane is being tracked by radar at O.

  Smply supported beam l1l2 m long carries a point load gk

simply supported beam l1l2 m long carries a point load gk a kn qk b kn at mid-span and its self-weight with fire

  Disposal of excavated material

Discuss and use examples to explain the specific factors that you will need to consider when pricing the following items in the bill of quantities foundation excavation

  Using finite element method to find temperature of the poker

The temperature of the poker at the third points of the poker using three elements of equal length. Use the finite element method. You may use Mathcad to solve this problem. If you do, please show all work and add comments to the Mathcad solution ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd