Determine the slope of the line when the plate is subjected

Assignment Help Civil Engineering
Reference no: EM13546886

1.A line of slope 4:10 has been scribed on a coldprolled yellow-brass plate, 6 in. wide and 1/4 in. thick. Using the data available in Appendix B, determine the slope of the line when the plate is subjected as shown to a 45-kip centric axial load.

2.It rains 3.0 in. on a 20.0 acre watershed. What is the volume of rainfall excess if 30% of the watershed area is a lake and infiltration on the soil is estimated at 1.0 in? What is the total volume of runoff? Express your answer in cubic feet. Assume that the lake level is low and does not contribute to rainfall excess. Hint: Lakes are treated as initial abstraction.

Reference no: EM13546886

Questions Cloud

What is the effective vertical pressure due to the weight : The initial velocity of a 15-lb block is given as mv1=15i+15j (ft/s). A force defined by F=250i-250tj (lb) acts on the particle from time t=0 to time t=0.3 s for a total duration of 0.3 s. Determine the particle’s velocity at t=1 s. Neglect friction.
Determine the magnitude of the average force acting : Determine the magnitude of the average force acting on a highway bumper when a 5000-lb car traveling at 60 mph crashes against it. The time interval during which the car is brought to rest is 0.3 s.
List assumptions for the other variables of the hydro logic : Estimate the amount of depression storage (inches and cubic feet) in a 6-arce parking lot using the following rainfall and discharge data. The discharge data were measured at the only outlet in the parking lot.
Determine the total force needed to overcome axle friction : A 100-ton train traveling on a horizontal track requires 400 hp to maintain a constant speed of 50 mi/h. Determine (a) the total force needed to overcome axle friction, rolling resistance, and air resistance
Determine the slope of the line when the plate is subjected : A line of slope 4:10 has been scribed on a coldprolled yellow-brass plate, 6 in. wide and 1/4 in. thick. Using the data available in Appendix B, determine the slope of the line when the plate is subjected as shown to a 45-kip centric axial load.
Which beam has the largest maximum moment : Consider two beams, which are loaded the same but have different support conditions. Which beam has the largest maximum moment? First, find support reactions, and then plot axial force (N), shear (V)
Calculate the maximum deflection of the beam : A 30" beam with a cross section of 1" wide and 2" tall is supported by a pin at point A on its left end, and a roller at point B on its right end. A 300 lb force is exerted 10" to the right of A (20" left from B), and a 600lb force is exerted 20" to ..
How much money will be saved in energy each year : An electric water heater held at 140 °F is kept in a 70 °F room. When purchased, its insulation is equivalent to R-5. An owner puts a 25-ft2 blanket on the water heater, raising its total R value to 15.
Determine the veolicty of the cart at the instant package : A 20-lb package is thrown with a speed of 9 ft/s onto the 100-lb cart at the given angle of 30 degrees. It slides on the smooth cart and strikes the spring. If the spring has a spring constant k= 200 lb/in

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the normal depth-velocity and the froude number

A PVC pipe with a diameter of 30 inches will carry a flow of 20 cfs. the bottom slope is 0.005 and the roughness coefficient is 0.015. determine the normal depth, critical depth, velocity and the froude number.

  Determine the detention time in hours for the chemostat

Perform a material balance on substrate (S) around a chemostat (completely mixed reactor without recycle) assuming a first-order removal for a substrate with a rate constant of 0.5 hr-1.

  Calculate the rate of removal and the rate constant

A toxic compound being is removed from solution in a CSTR at Steady State according to a first order reaction rate. The upstream concentration of the pollutant is 14 mg/L and the downstream concentration is 1.7 mg/L.

  Determine max torque that can be carried by hollow section

A 32-in.-wide by 0.125-in.-thick by 110-in.-long steel sheet is to be formed into a hollow section by being bent through 360° and having the long edges welded (i.e., butt-welded) together. Assume a cross-sectional medial length of 32 in.

  Find the maximum columm load for asd dead-live-roof load

A 4x4 carries an axial compressive force caused by dead, love, and roof live loads. Lumber is No. 1 Douglas Fir-Larch. Cm = 1.0 , Ct = 1.0, Ci = 1.0. The unbraced length of the member is 12 ft.

  What is the factor of safety against sliding

a concrete dam retaining water has a specific weight of concrete of 23.5kn/m3, what is the factor of safety against sliding & overturning and pressure intensity on the base if coefficient of friction is 0.45.

  At what angle did the player have to shoot the cue ball

(a) At what angle did the player have to shoot the cue ball so that the eight ball entered the pocket at C? (b) In what direction did the cue ball move after the collision? (c) What percentage of its kinetic energy did the cue ball impart to the e..

  Express samples hardness in meq per l and mg per l of caco3

Hardness is sum of all divalent cations (meaning all species with a positive charge of 2) in a water sample. Magnesium (Mg2+) and calcium (Ca2+) are the most common divalent cations that contribute to hardness.

  Express will the two drops collide in standard air

A 5-micron droplet of water is being carried in standard air toward a 500-micron drop of water at a relative velocity of 40m/s. Will the two drops collide

  Determine what is the total energy per unit mass

A fluid in an aquifer is 23.6m above a reference datum; the fluid pressure is 4390 N/m2. The fluid density is 0.999E3 kg/m3. What is the total energy per unit mass What is the total energy per unit weight

  What is the main objective of nasas mars science laboratory

Q. What is the main objective of NASA's Mars Science Laboratory (MSL) mission? When was it launched and when and where is it scheduled to land on Mars? Explain the major differences between this mission and Mars Exploration Rovers (MER) mission?

  Calculate minimum-sized sand particle that would be removed

Calculate the minimum-sized sand particle that would be removed in the chamber. To be removed, the particles must settle the depth of 2 m during the period the wastewater spends in the chamber (dT=V/Q).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd