Which beam has the largest maximum moment

Assignment Help Civil Engineering
Reference no: EM13546885

Consider two beams, which are loaded the same but have different support conditions. Which beam has the largest maximum moment? First, find support reactions, and then plot axial force (N), shear (V), and moment (M) diagrams for both beams. Label all critical N, V, and M values and also the distance to points where N, V, and M is zero.

Reference no: EM13546885

Questions Cloud

Determine the magnitude of the average force acting : Determine the magnitude of the average force acting on a highway bumper when a 5000-lb car traveling at 60 mph crashes against it. The time interval during which the car is brought to rest is 0.3 s.
List assumptions for the other variables of the hydro logic : Estimate the amount of depression storage (inches and cubic feet) in a 6-arce parking lot using the following rainfall and discharge data. The discharge data were measured at the only outlet in the parking lot.
Determine the total force needed to overcome axle friction : A 100-ton train traveling on a horizontal track requires 400 hp to maintain a constant speed of 50 mi/h. Determine (a) the total force needed to overcome axle friction, rolling resistance, and air resistance
Determine the slope of the line when the plate is subjected : A line of slope 4:10 has been scribed on a coldprolled yellow-brass plate, 6 in. wide and 1/4 in. thick. Using the data available in Appendix B, determine the slope of the line when the plate is subjected as shown to a 45-kip centric axial load.
Which beam has the largest maximum moment : Consider two beams, which are loaded the same but have different support conditions. Which beam has the largest maximum moment? First, find support reactions, and then plot axial force (N), shear (V)
Calculate the maximum deflection of the beam : A 30" beam with a cross section of 1" wide and 2" tall is supported by a pin at point A on its left end, and a roller at point B on its right end. A 300 lb force is exerted 10" to the right of A (20" left from B), and a 600lb force is exerted 20" to ..
How much money will be saved in energy each year : An electric water heater held at 140 °F is kept in a 70 °F room. When purchased, its insulation is equivalent to R-5. An owner puts a 25-ft2 blanket on the water heater, raising its total R value to 15.
Determine the veolicty of the cart at the instant package : A 20-lb package is thrown with a speed of 9 ft/s onto the 100-lb cart at the given angle of 30 degrees. It slides on the smooth cart and strikes the spring. If the spring has a spring constant k= 200 lb/in
Determine the magnitudes of the horizontal and vertical : A man having the mass of 77 kg sits in the chair which is pin-connected to the frame BC. If the man is always seated in an upright position, determine the magitudes of the horizontal and vertical reactions of the chair

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the largest load p that can be applied

If each cable segment can support maximum tension of 75 lb, determine the largest load P that can be applied.

  Which direction to apply the force components

When drawing a FBD, how do you know which direction the x, y and z components are applied? I know that the sum of forces in each direction and the moments about each axis have to equal zero so I know some FBD are pretty self explanatory

  Design the shear reinforcement

Problem Statement: A rectangular beam having b = 10 in. and d = 17.5 in. spans 15 ft face to face of simple supports. It is reinforced for flexure with three

  Write the general mass balance equation for the rinse tank

To remove the solution containing metal from a part after plating the part is commonly rinsed with water. The rinse water is contaminated with metal and must be treated before discharge. The Shiny Metal Plating Co. The plating solution contains 85..

  Determine the reactions at the supports by a rocker

The compound beam is fixed at A and supported by a rocker at B and C. There are hinges (pins) at D and E. Determine the reactions at the supports.

  Determine the power generated by turbine in steady state

Determine the power generated by the turbine (in KW) operating in steady state at 5MPa, with specific enthalpy 3000kj/kg and velocity of 10m/s at the entrance and steam escaping at 0.07MPa, specific enthalpy 2000kj/kg at velocity of 90m/s p.

  Determine the diameter and the depth of the tank

A drinking water treatment plant will be designed to process a flow of 15,000 m3/d. The sedimentation tank will have a residence (detention) time of 4 hours and the overflow rate (Q/A) of 16 m3/m2-day

  You are working as a project analyst for the local gas

you are working as a project analyst for the local gas utility and you have been placed on a project to install an

  What is the tce concentration in ppm if the tank is held

What is the TCE concentration in ppm if the tank is held at (a) 4 degrees C and (b) 35 degrees C (c) What is the TCE concentration in ppm if the tank is filled with hexane instead of water

  Under what circumstances is there an exception to law

under what circumstances is there an exception to the general law that an identified original section corner controls the positions of the boundary lines meeting at or passing through the corner

  Determine what the forces are in the ax and ay directions

After drawing a free body diagram, how do you determine what the forces are in the Ax, Ay directions, etc. without being given any numbers

  Find the angular acceleration of the plate at the instant

An external moment of magnitude 110 N-m is applied in the counter clockwise direction as shown. A frictional moment of magnitude 10 N-m resists the rotation. The specific weight of the material is 250 lbs / ft3.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd