Calculate the maximum deflection of the beam

Assignment Help Civil Engineering
Reference no: EM13546884

A 30" beam with a cross section of 1" wide and 2" tall is supported by a pin at point A on its left end, and a roller at point B on its right end. A 300 lb force is exerted 10" to the right of A (20" left from B), and a 600lb force is exerted 20" to the right of A (10" left of B).

Using singularity functions for beam deflection, calculate the maximum deflection of the beam and its correspoinding horizontal distance from A.

Reference no: EM13546884

Questions Cloud

List assumptions for the other variables of the hydro logic : Estimate the amount of depression storage (inches and cubic feet) in a 6-arce parking lot using the following rainfall and discharge data. The discharge data were measured at the only outlet in the parking lot.
Determine the total force needed to overcome axle friction : A 100-ton train traveling on a horizontal track requires 400 hp to maintain a constant speed of 50 mi/h. Determine (a) the total force needed to overcome axle friction, rolling resistance, and air resistance
Determine the slope of the line when the plate is subjected : A line of slope 4:10 has been scribed on a coldprolled yellow-brass plate, 6 in. wide and 1/4 in. thick. Using the data available in Appendix B, determine the slope of the line when the plate is subjected as shown to a 45-kip centric axial load.
Which beam has the largest maximum moment : Consider two beams, which are loaded the same but have different support conditions. Which beam has the largest maximum moment? First, find support reactions, and then plot axial force (N), shear (V)
Calculate the maximum deflection of the beam : A 30" beam with a cross section of 1" wide and 2" tall is supported by a pin at point A on its left end, and a roller at point B on its right end. A 300 lb force is exerted 10" to the right of A (20" left from B), and a 600lb force is exerted 20" to ..
How much money will be saved in energy each year : An electric water heater held at 140 °F is kept in a 70 °F room. When purchased, its insulation is equivalent to R-5. An owner puts a 25-ft2 blanket on the water heater, raising its total R value to 15.
Determine the veolicty of the cart at the instant package : A 20-lb package is thrown with a speed of 9 ft/s onto the 100-lb cart at the given angle of 30 degrees. It slides on the smooth cart and strikes the spring. If the spring has a spring constant k= 200 lb/in
Determine the magnitudes of the horizontal and vertical : A man having the mass of 77 kg sits in the chair which is pin-connected to the frame BC. If the man is always seated in an upright position, determine the magitudes of the horizontal and vertical reactions of the chair
What is its angular speed 0.1 seconds later : A disk of radius 0.2m and moment of inertia 1.5 kg*m^2 is mounted on a nearly frictionless axle. A string is wrapped tightly around the disk, and you pull on the string with a force of 25 N. After w while the disk has reached an angular speed ..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the heat and work excahnged during the process

a piston-and-cylinder device contains 5 kg of water initially at 150 C and 0.20 MPa. The frictionless piston is then pushed slowly in an isothermal process until the volume of water becomes 10% of its initial value.

  Find the value of k

time(in months) after a computer of brand is sold and needed repair is normally distributed with mean 36 months and standard deviation 4 month. if 1% of the super computer need services less than k months after they are sold, find the value of k.

  Determine the minimum required vehicle frequency

A light rail route has 2 terminals and 4 intermediate stations. The demand (passengers/hr) for morning peak hour is: North Terminal Station 1 Station 2 Station 3 Station 4 South Terminal

  What contour intervals will be drawn if a 50ft interval

An area that varies in elevation from 463ft - 634ft is being mapped. What contour intervals will be drawn if a 50ft interval is used? Which lines are emphasized?

  Calculate what is the porosity of the sand

You have a beaker filled with coarse sand. The capacity of the beaker is 100cm^3. Next, you add to the beaker 40cm^3 of distilled water, filling the water level exactly to the top of the sand.

  Under what situation shall engineers use jacking at one end

Sometimes the side of concrete bridges is observed to turn black in colour. What is the reason for this phenomenon? In prestressing work, if more than one wire or strand is included in the same duct, why should all wires/strands be stressed at the sa..

  What will be the effect of making an indentation very close

When making hardness measurements, what will be the effect of making an indentation very close to a preexisting indentation. Why.

  Revolve the pavement about its inside edge

Calculate the super-elevation required for a horizontal curve on a two-lane, two- way highway with 60 mph design speed, and a 1200 ft. radius curve. What is the required length of the spiral curve?

  Calculate the energy needed to bring the soil

We are digging a hole to build a building. Calculate the energy needed to bring the soil to surface level. Remember the sides of the excavation lie at 45 degrees. Else, the whole would be constantly refilling itself.

  Who has been offered a 5-year contract at a remote location

Suzanne is a recent chemical engineering graduate who has been offered a 5-year contract at a remote location. She has been offered two choices. The first is a fixed salary of $75,000 per year.

  Determine the heights of the fluid columns for barometers

Determine the heights of the fluid columns for barometers that use the following liquids at 20 C: water, ethyl alcohol, and mercury. Why do you think mercury barometers were used in the past (before the negative health effects of mercury were know..

  Determine what is the normal stress at the fixed support

The rod has a uniform cross-section of 53mm2. The external load consists of point loads: two P1 of 3kN, two P2 of 1kN, and one P3 of 7kN. What is the normal stress at the fixed support

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd