Classify the jump type and calculate the energy lost

Assignment Help Civil Engineering
Reference no: EM13552924

A rectangular channel of width 12 ft has an upstream slope of 0.02 ft/ft and a downstream slope of 0.0005 ft/ft. Both reaches have lengths of 500 ft. The upstream reach has a Manning's roughness of 0.016 and the downstream reach has a roughness of 0.011. The design discharge is Q = 460 cfs, the low discharge is Q = 230 cfs, and the flood discharge is Q = 690 cfs. Using the direct step method by hand with 1 step, determine the location of the hydraulic jump relative to the slope break for the design discharge. Classify the jump type and calculate the energy lost.

Reference no: EM13552924

Questions Cloud

Determine the diameter of the pipe assume smooth transition : It is required to reduce a pipe of diameter 8 in to a minimum diameter pipe that allows the downstream velocity not to exceed twice the upstream velocity. Determine the diameter of the pipe. Assume smooth transition
Construct a choice table for interest rates from 0% to 100% : A firm is considering moving its manufacturing plant from Chicago to a new location. The industrial engineering department was asked to identify the various alternatives together with the costs to relocate the plant, and the benefits.
Find the volume of the given solid region bounded : Find the volume of the given solid region bounded below by the cone z=sqrt(x^2+y^2) and bounded above by the sphere x^2+y^2+z^2=128. using triple intergrals
Determine this deflection and the proper offset d : The two I-beams are welded together and are initially supported by the three cables of equal length hanging vertically from supports directly above A, B, and C. When applied with the appropriate offset
Classify the jump type and calculate the energy lost : A rectangular channel of width 12 ft has an upstream slope of 0.02 ft/ft and a downstream slope of 0.0005 ft/ft. Both reaches have lengths of 500 ft. The upstream reach has a Manning's roughnes
Find the maximum bending stresses : A simply supported composite beam 3m long carries a uniformly distributed load of intensity q=3.0kN/m. the beam is constructed of a wood member, 100mm wide by 150mm deep
What will it be after consolidation is completed : The current vertical stress at a point in a saturated clay is 181 kPa. This soil is to be covered with a 2.5m thick fill that will have a unit weight of 19.3 kN/ m^3. What will be the value of the vertical
What is friction of k and how does it work into the reaction : A 400 lb crate is on a 20 degree incline. If a 120 lb horizontal force (P), pushes on the crate (upwards), determine the normal and frictional forces acting on the crate. Take friction of surface = 0.3 and friction of k = 0.2?
Determine the location of the hydraulic jump relative : A rectangular channel of width 12 ft has an upstream slope of 0.02 ft/ft and a downstream slope of 0.0005 ft/ft. Both reaches have lengths of 500 ft. The upstream reach has a Manning's roughness of 0.016 and the downstream reach has a roughness of 0...

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine volume of three identical activated sludge tanks

Determine the volume of three identical activated sludge tanks following primary clarification to aerate 36,000 m cubed/d with a BOD concentration of 180 mg/l at a BOD loading of 560 g/m cubed*d.

  Calculate the quality of the steam exiting heat exchanger

A chemical plant uses a tube-­within-­a-­tube counterflow heat exchanger to heat air with the use of steam. During steady state operation, the air flows into the exchanger at a rate of 5,000 kg/h and a temperature of 27C and exits at a temperature..

  What would height be after it was consolidated into packing

A 1m thick layer of this soil is packed so that it is as loose as possible (void ratio, e_max ~= 0.9), and then it was vibrated until it was as dense as possible (void ratio, e_min ~= 0.35).

  Determine the amount of money saved per year associated

A 2005 Chrysler Town and Country MInivan has a frontal area of 2.9m2 and a drag coefficient of 0.35. A 2000 Honda Insight has a frontal area of 1.9m2 and a drag coefficient of 0.25.

  Assume a future where security countermeasures against dos

assume a future where security countermeasures against dos attacks are much more widely implemented than at present. in

  How much must you deposit monthly between ages 24 and 66

You wish to retire at age 66 and at the end of each month thereafter for 30 years, to receive $5000. Assume that you begin making monthly payments into an account at age 24. You continue these payments until age 66. If the interest rate is constant a..

  Calculate the wet density in pounds per cubic feet

A small chunk of the original sample had a wet weight of 140.9 grams and weighed 85.2 grams after drying. Compute the water content, using the correct number of significant figures.

  Calculate the torque required to rotate the inner shaft

a 4ft-long, 1-in-diameter shaft rotates inside an equally long cylinder that is 1.02 in. in diameter. Calculate the torque required to rotate the inner shaft at 2000 rpm if SAE-30 oil at 70 degrees F fills the gap

  Explain how the difference in piezometric pressure

A manometer is used to measure the pressure difference between points A and B in a pipe. Water flows in the pipe, and the specific gravity of the manometer fluid is 2.8. The distances and manometer deflection are indicated.

  Design the pipe to flow capacity and use a mannings n

Determine the diameter (in inches) and velocity (feet per second) of a concrete storm pipe required to carry a peak flowrate of 20 cfs at a slope of 1.0% Design the pipe to flow at 75% capacity and use a Mannings n of 0.013.

  Net rate of flow of linear momentum via control surface

Measurements indicate that to cause this flow the force acting on the contents of the control volume is 40i lb. Determine the net rate of flow of linear momentum through the control surface.

  Show process on t-v diagram with respect to saturation line

An insulated rigid tank is initially filled with a saturated liquid-vapor mixture of water. Initially three-quarters of the mass is in the liquid phase, the mass is 10 lbm, and the pressure is 15 psia.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd