Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A firm is considering moving its manufacturing plant from Chicago to a new location. The industrial engineering department was asked to identify the various alternatives together with the costs to relocate the plant, and the benefits. The engineers examined six likely sites, together with the do-nothing alternative of keeping the plant at its present location. Their findings are summarized as follows:
Plant Location First Cost ($000s) Uniform Annual Benefit ($000s)
Denver $300 $ 52
Dallas 550 137
San Antonio 450 117
Los Angeles750 167
Cleveland 150 18
Atlanta 200 49
Chicago 0 0
The annual benefits are expected to be constant over the 8-year analysis period.
(a) Construct a choice table for interest rates from 0% to 100%.
(b)IT the firm uses 10% annual interest in its economic analysis, where should the manufacturing plant be located. (Answer: Dallas)
Use MARR=15%, and only use Excel to check your results!
Calculate the super-elevation required for a horizontal curve on a two-lane, two- way highway with 60 mph design speed, and a 1200 ft. radius curve. What is the required length of the spiral curve
Determine the design compressive strength for a pinned ended HSS 8x8x3/8 column of ASTM A500, grade B steel with an unbraced length of 35ft
A tracer dye is injected into a 55-ft thick sandy gravel confined aquifer which has a hydraulic conductivity of 1.2 x 10^-3 ft/s. The dye appears 14 days later in an observation well 75 ft away from the injection point.
A steel rod having a cross sectional area of 1/2in^2 and length of 600ft is suspended vertically. It supports a load of 5000 pounds at the lower end. If steel weighs 490 lb/ft^3 and E=30,000,000 psi, find the total elongation of the rod
A lagoon with volume 1200 m3 has been receiving a steady flow of a conservative waste at a rate of 100 m3/day for a long enough time to assume that steady-state conditions apply. The waste entering the lagoon has a concentration of 10 mg/L. Assuming ..
1nbsp surveying iimagnetic compass the most common type of compass is the magnetic compass which is used to determine
A “Cold Air-Standard Brayton cycle” gas-turbine power plant delivers a net power output of 60 MW to an electric generator. The compressor intake temperature is 300 K and the maximum temperature in the cycle is 1200 K.
Suppose that in an apparatus it is necessary to maintain precisely the cross section of a 20mm circular nickel steel bar. If this bar is heated to 200 deg Celcius, what tensile force should be applied to the bar to maintain its cross sectional dim..
A newly designed dam is to be modeled in the laboratory. The prime objective of the general model study is to determine the adequacy of the spillway design and to observe the water velocities, elevations, and pressures at critical points of the st..
the pressure inside a commercial airliner is maintained at 1.00 ATM. what is the net upward force exerted on a (1.0 m)(200 cm) cabin door if the outside pressure is 0.30 ATM?
The boiling water passes through copper pipes that have a wall thickness of 4 millimeters and a surface area of 0.12 square meters per meter length of the pipe. Find the total length of pipe (there are actually many pipes in parallel)
The road is in good, dry conditions until 160 ft before the stalled car where it is wet and stays wet for the remaining length. What is the minimum distance from the stalled car at which the driver could apply the brakes and still stop before hitt..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd