With what velocity will air enter the room under

Assignment Help Civil Engineering
Reference no: EM13555149

1.The strain in member AB was measured to be 8.9*10-4. If the member is an L3*2 1/2* 1/4 of A36 steel determine the following:

a) What is the change in length in inches?

b) What is the force in the member?

2.Laboratories containing dangerous materials are often kept at a pressure slightly less than ambient pressure so that contaminants can be discharged through an exhaust system rather than leaked through cracks and around doors to other parts of the building. If the pressure in a laboratory is 0.1 inch of water below that of a hallway, with what velocity will air enter the room under the laboratory door? Assume viscous effects are negligible.

Reference no: EM13555149

Questions Cloud

Determine lengths l1 and l2 so the two materials elongate : A solid cylinder of 50 mm diameter and 900 mm length is subjected to a tensile force of 120kN. One part f the cylinder L1 long is of steel, the other part
What is the percentage error in the bulk unit weight : What is the percentage error in the bulk unit weight if the soil is the percentage error in the bulk unit weight if the soil is 95% saturated but assumed to be 100% saturated?
What must be the allowable elongation : A cylindrical rod of brass alloy (E = 100 GPa,) having a yield strength of 345 MPa is to be subjected to a load of 7500 N. If the length and diameter of the rod are 338 mm and 7.55 mm respectively, what must be the allowable elongation?
What should be the concentration of pollutant : A lagoon with volume 1,200 m3 has been receiving a steady flow of a conservative waste at a rate of 100 m3/day for a long enough time to assume that steady-state conditions apply. The waste entering the lagoon has a concentration of 10 mg/L. assuming..
With what velocity will air enter the room under : Laboratories containing dangerous materials are often kept at a pressure slightly less than ambient pressure so that contaminants can be discharged through an exhaust system rather than leaked through cracks and around doors to other parts of the bui..
What concentration of ozone should be injected : Ozone is sometime used as a disinfectant for drinking water. Ozone is highly reactive it will react benign species found in water, as well as the pathogens it is intended to kill.
Determine the percentage increase in the discharge : As part of a drainage improvement project, a drainage ditch will be straightened and cleaned. As a result, the lenght of the ditch will decrease from 1800 ft to 1400 ft and the mannings roughness factor will be reduced
What will be the porosity of the mixture : You are furnished with three sizes of particles. One is gravel with porosity of 0.32, the second is a coarse grained sand with porosity of 0.37, and the third is a fine grained sand with porosity of 0.23. If the coarse grained sand
Determine redox state of sulfur in both the compounds : Derive the porosity values for cubic, orthorhombic, and rhombohedral packing of spheres. Include sketches supporting your calculations of the bulk volumes of the unit cells.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Factors of safety against sliding and against overturning

Determine the factors of safety against sliding and against overturning, and also the soil pressure at the heel and toe. Assume hydrostatic uplift varies uniformly from full hydrostatic head at the heel of the dam to zero at the toe. consider 1m l..

  Determine location of the centroid relative to the channel

A trapezoidal river channel section has a base dimension of 30 feet, a liquid depth of 4 feet, and side slopes of 4 to 1 (horizontal to vertical).

  Determine thethickness of the water layer under the runners

A sled with two runners slides along a thin horizontal layer ofwater between the ice and the runners. The horizontal force thatthe water puts on the runners is equal to 1.2 lb when the sled'sspeed is 30 ft/s.

  Determining transformed moment of inertia

Determine the transformed moment of inertia for the beam using steel as the reference material. Express your answer in in^4 to the nearest 0.1 in^4.

  Calculate for the whole catchment values of annual average

A watershed has four sub-areas. The annual precipitation and evaporation from each of the sub-areas are given in Table(below). Assume that there is no change in groundwater storage on an annual basis and calculate for the whole catchment the value..

  What will be the discharge through the pipe

A pump having the characteristics given ( N=2133.5 rpm, n=35.6 rps, D=37.1 cm) pumps water at 25 degree C from a reservoir at an elevation of 366 m to a reservoir at an elevation of 450 m through a 36 cm steel pipe

  Determine the prism constant

To verify the constant of a particular prism, a straight line EFG is laid out. The EDM instrument is first set up at E, with the following measurements recorded: EG = 426.224 m, EF = 277.301 m

  Compute the ratio of the nominal flexural strength

Compute the ratio of the nominal flexural strength of the beam to the maximum service load moment, and compare your findings to the ACI load factors and strength reduction factor.

  Determine the minimum distance from the diversion that a

A temporary diversion has been constructed on a highway of +4 percent gradient due to major repairs that are being undertaken on a bridge. The maximum speed allowed on the diversion is 10 mph

  Determine the maximum allowable compressive force

(a) Determine the desired diameter of the disk. (b) If the rubber strain is not to exceed 0.2 in/in, determine the maximum allowable compressive force. Recall that the spring constant, k=Fx,or in terms of an axially loaded member

  Determine what will current be and what will the power be

suppose we have a 100-volt battery connected with a 100-ohm resistance. The current is then 100/100=1 amp. how much power is produced. if we double the voltage, what will the current be and what will the power be.

  How high a column of ethyl alcohol would be required

How high (m) a column of ethyl alcohol would be required to give the same pressure as 700 mm Hg

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd