What will the ammonia concentration be 10 miles downstream

Assignment Help Civil Engineering
Reference no: EM13549258

A river that behaves as a plug flow reactor has a flow rate of 250 cfs with an average velocity of 1.25 ft/s. The concentration of ammonia is 6 mg/L at one point in the river. If the first – order decay coefficient for the conversion of ammonia to nitrate is 0.05 day-1, what will the ammonia concentration be 10 miles downstream.

Reference no: EM13549258

Questions Cloud

Estimate its drag assuming fully turbulent flow : Airplane tows a 2m tall advertising banner at a speed of 160 Km/hr. If the banner is flat and 5m long, then estimate its drag assuming fully turbulent flow.
Estimate the lateral strain experienced by the bar : A 1.0-m rigid horizontal support is hung by two cables as shown. One cable is brass and The other cable is high-density polyethylene plastic. At room temperature (21°C), the cables measure 3.50 m vertically. When the temperature drops to 15°C, find t..
Determine the torque that develops in the rod : The end of a 0.75-in-diameter rod is fixed to an immovable plate as shown. The length of the rod is 18.0 in. A 50-lb weight is attached to a 16.0-in lever at the end of the Rod so that the weight is hanging perpendicular to the longitudinal axis of t..
The change in length of the cable when the beam is under : A 4-m-long rigid beam is supported by a pinned connection and cable. the beam weighs 2.0 kn and hangs horizontally when unloaded When the beam is not loaded the solid cable is 4.00 m long and has a solid area of 175 mm1
What will the ammonia concentration be 10 miles downstream : The concentration of ammonia is 6 mg/L at one point in the river. If the first – order decay coefficient for the conversion of ammonia to nitrate is 0.05 day-1, what will the ammonia concentration be 10 miles downstream.
What is the normal depth in a 4-foot wide rectangular : What is the normal depth in a 4-foot wide rectangular channel that conveys a discharge of 100 CFS and has a bed slope of 2% with a Manning’s roughness coefficient of 0.025? a).1.3 feet b).2.7 feet c).4.4 feet d).6.2 feet
How many gallons would be required to last the same time : How many gallons would be required to last the same time as the gas? The sodium hypochlorite solution strength is 15 percent by weight and has the same unit weight as water (specific gravity 1.0). One pound of sodium hypochlorite has the same disinfe..
What concentration would correspond to a risk : The drinking water standard for dioxin is 3 x 10-8 mg/L. Using EPA exposure factors for residential consumption, what lifetime risk would this pose? What concentration would correspond to a risk of 10-6? The following data and assumptions apply: Data..
What is the volume of the lake in cubic feet : A shallow lake can be considered a CFSTR. Nitrification, the conversion of ammonia to nitrate (NH3 -> NO3-) occurs in the lake according to first – order kinetics. One stream feeds the lake and one stream empties the lake with the flow rate in both b..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the volume flow rate of water

Water with a static pressure of 1.96kN/M 2 flows through an 800 mm diameter pipe. A pitot tube pressure gage in this pipe reads a pressure of 5.88 kN/M 2 . How do you determine the volume flow rate (Q) of the water? (Q = 1.40 M^3/sec, V=2.79 M/se..

  Find the velocity at which shuttle hits the player bs racket

In Singles badminton game, shuttle is smashed by Player A from close to base line, which is 6 m from the net. Height of the net to be cleared by a smash is 1.55 m. The shuttle is hit by player A at a speed of 250 km/h.

  Determine the magnitude of the axial force in members

The symmetrical scissors truss shown below is supported atpoint A and D. The support at D is a rocker bearing and does notproduce a horizontal reaction. A, B, C, D, E & F are pinjoints.

  Civil engineering - structure designplease write reflective

civil engineering - structure designplease write reflective report for structural design of reinforced cast in - place

  Determine what is the average shear stress in the oil

Two parallel plates, one moving at 4m/s and the other fixed, are seperated by a 5mm thick layer of oil of specific gravity 0.80 and kinematic viscocity 1.25 X 10^-4 m2/s.

  Find the pressure head at the lower end of the pipe when the

Base course aggregate has a target dry density of 119.7 lb/cu ft in place. It will be laid down and compacted in a rectangular street repair area of 2000 ft*48ft*6in.

  Find what is the degree of saturation of the field sample

Let us pretend you are an earthwork construction control inspector and you are checking the field compaction of a layer of soil. After compaction in the field, the density of soil was checked by excavating part of the compacted soil

  Determine the height of the step in the channel botom

A 50 meter wide rectangular channel is carrying a flow of 250 m3/s at a flow depth of 5 meters. To produce critical flow in this channel, determine a.) the height of the step in the channel botom if the width remains constant.

  Determine the length of the middle ordinate

a simple horizontal curve has a central angle of 35 degrees-40 minutes-40 seconds, and a degree of cure (arc definiton) of 5 degrees -00 minutes-00 seconds.

  What percentage removal should be expected for particles

What percentage removal should be expected for each of the following particle settling velocities in an ideal sedimentation tank: 0.1 mm/s, 0.2 mm/s, 1 mm/s.

  Determine the temperature rise that will cause joint to fail

the block is fitted between the fixed supports. if the glued joint can resist a maximum shear stress of T(allow)=2ksi, determine the temperature rise that will cause the joint to fail. Take E= 10(10^3)ksi, v=0.2

  How to express the variables as a dimensionless group

The velocity of propagation, c of surface waves is assumed to depend on the water depth, y, the water density, and the acceleration due to gravity, g. Express these variables as a dimensionless group.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd