What types of proteins had to have been degraded to isolate

Assignment Help Civil Engineering
Reference no: EM13531074

1.A 6ft coal seam at a depth of 750ft is tobe mined by a room-and-pillar system incorporating 16ft entries andpillars that are 50ft square. The K value for the seam is4,000. Utilizing the Bieniawski formula, determine if thesedimensions provide adequate stability.

2.What types of proteins had to have been degraded to isolate theDNA? Why is DNA considered to be an acid?

Reference no: EM13531074

Questions Cloud

What is the composition of the last solid remaining prior : What is the composition of the last solid remaining prior tocomplete melting?
Determine the concentration of carbon in this alloy : The microstructure of an iron-carbon alloy consistsof proeutectoid ferrite and pearlite; the mass fractions of thesetwo microconstituents are 0.174 and 0.826, respectively. Determinethe concentration of carbon in this alloy.
What must be its composition if this is notpossible : It is desirable to produce a copper-nickel alloythat has a minimum noncold-worked tensile strength of 380 MPa(55,000 psi) and a ductility of at least 45% EL. Is such an alloypossible? If so, what must be its composition? If this is notpossible, then ..
What is the composition of the ß phase : A hypothetical A-B alloy of composition 40 wt%B-60 wt%A at sometemperature is found to consist of mass fractions of 0.66 and 0.34for the αand β phases, respectively. If the composition of the α phase is 13 wt% B-87 wt% A, what is the composition ofth..
What types of proteins had to have been degraded to isolate : What types of proteins had to have been degraded to isolate theDNA? Why is DNA considered to be an acid?
What is the total lenth ac and its standard deviation : A line AC was observed in 2 sections AB and BC, with lengthsand standard deviations listed below. What is the total lenth AC and its standard deviation?
How to find the cp and cpk : Determine Cp and Cpk for this process. Comment on processcentering and stability. the specification range is0.500+/-0.005
Male coloration is not relevant to this question : Apopulation of pheasants is released onto 6 islands. The pheasantcame from the mainland where predators are common. Three of theislands have predatory fox present (have-predators) and three donot have fox present (predator-free)
Find the angular acceleration of the disk and the tangential : A unform disk of radius R and mass M is mounted on an axle supported on a fixed frictionless bearing. A cable is wrapped around the rim of the wheel and a steady

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is magnitude of total external force on the helicopter

During a test flight in which a 9000-kg helicopter starts from rest at t = 0, the acceleration of its center of mass from t =0 to t =10 s is a=(0.6t)i+ (1.8 0.36t)j m/s2.

  Find the flow rate if the pump puts 22 hp in to the flow

At A, the pipe diameter is 24 in and the pressure is 45 psi. At B, the pipe diameter is 12 in and the pressure is 50 psi. Point B is 3 f t lower than A. Find the flow rate if the pump puts 22 hp (16 kW) in to the flow. Neglect head losses.

  Estimate the shear strength on a horizontal plane at a depth

A site is underlain by a soil that has a unit weight of 118 lb/ft^3. From laboratory shear strenght tests that closely simulated the field conditions, the total stress parameters were measured to be C_T=250 lb/ft^2

  What is the speed of the bug as seen by the man at the side

A bug is crawling up the leg of a man on a train. The velocity of the bug relative to the man is 0.3 m/s k . The mas is waling from one side of a carriage to the other with a vlocity relative to the train of 1.2 m/s j.

  What is the maximum length to which it may be stretched

what is the maximum load that may be applied to a specimen with a cross sectional area of 130 mm^2 without plastic deformation.

  What is the local acceleration midway along the nozzle

the velocity varies linearly with time throughout the nozzle. the velocity at the base is 1t and at the tip is 4t. what is the local acceleration midway along the nozzle when t=2s

  Calculate the coefficient of consolidation

For the soil and foundation conditions in fig. 1, determine the time required to reach 75% consolidation in the clay given the consolidation test results and determine the coefficient of consolidation

  How much salt should be removed per day from plant effluent

A pickle producing plant produces and discharges a waste brine solution with a salinity of 13,000 mg/L NaCl at a rate of 0.14 MGD into a stream.

  How many square inches of coating need to be applied

Workers plan to apply a reflective coating of paint to one surface of an equilateral triangular shaped highway sign. How many square inches of coating need to be applied to the sign if one side of the triangle is 12 inches

  How to compute the horizontal distance in elevation

The slope distance between two points is 72.665 m, and the difference in elevation between the points is 1.120 m. Compute the horizontal distance.

  Sufficient collapse strength

Would a 30 slot stainless steel screen (2.0 m long; located at the bottom of the well) have sufficient collapse strength for this application?

  Determine what is the torque of shaft be

if shaft A have 1200N.m torque with 25cm diameter and the shaft B have diameter of 52cm what is the torque of shaft be

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd