What is the speed of the train relative to

Assignment Help Civil Engineering
Reference no: EM13544575

A bug is crawling up the leg of a man on a train. The velocity of the bug relative to the man is 0.3 m/s k .

The mas is waling from one side of a carriage to the other with a vlocity relative to the train of 1.2 m/s j.

The train is travelling at 0.8 m/s i relative to a man on the side of the tracks. What is the speed of the bug as seen by the man at the side of the tracks? What is the speed of the train relative to (or as seen by) the bug?

Reference no: EM13544575

Questions Cloud

What is the minimum possible value for this pressure : Part of a vertical piping system consists of 8 ft of 4 in diameter, connected to 8 ft of 3 in diameter above, and connected to 8 ft of 2 in diameter above that. Water at 60 F flows up the pipe (no downward flow occurs)
What pressure must be provided at point 1 if you neglect : A pressure gage at elevation 4.8 m on the side of a storage tank containing oil reads 34.7 kPa.Another gage at elevation 2.2 m reads 57.5 kPa. Compute the specific weight, density, and specific gravity of the oil.
Find the steady-state concentration if the air is assumed to : Consider the air over a city to be a box 100 km on a side that reaches up to an altitude of 1.0 km. Clean air is blowing into the box along one of its sides with a speed of 4 m/s.
Suppose the utility encourages its customers to replace : Suppose a utility generates electricity with a 36 percent efficient coal-fired power plant emitting the legal limit of 0.6 lb of SO2 per million Btus of heat into the plant. Suppose the utility encourages its customers to replace their
What is the speed of the train relative to : The train is travelling at 0.8 m/s i relative to a man on the side of the tracks. What is the speed of the bug as seen by the man at the side of the tracks? What is the speed of the train relative to (or as seen by) the bug?
Determine the batch weights needed for all materials for : Determine the batch weights needed for all materials for a 1yd^3 batch yielding an f'c= 2500 psi given the following information.
What is the largest number of phases that can coexist at : Considering both temperature and pressure to be variables, what is the largest number of phases that can coexist at equilibrium in a binary alloy?
Calculate the volume of soil that will be needed if the void : A -4% grade and a 0% grade meeting at sta. 24 + 40 and elevation 2421.54 ft are joined by an 800-ft vertical curve. The curve passes under an overpass at sta. 25+00. If the lowest elevation of the overpass is 2439.93 ft, calculate the available clear..
Determine the stations and elevations of the bvc and evc : A 300 N force is applied at A as shown. Determine (a) the moment of the 300 N force about D, (b) the magnitude and sense of the horizontal force applied at C that creates the same moment about D, (c) the smallest force applied at C that creates the s..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the concentration of the pits overflow stream

A company has been discharging its waste into a holding pit for a long time. For the last several years, the pit has been full and overflowing into a local river. The waste concentration has been nearly constant at 10 mg/L of the pollutant of inte..

  Plot a curve showing the relationship of se versus

Plot a curve showing the relationship of Se versus L/r for steel columns. Draw the curve for slenderness ratios that vary from 0 to 200. Assume the proportional limit = 235 MPa

  Shafts in a speed-reducer unit

The two shafts in a speed-reducer unit are subjected to couples of magnitude M1 = 18 N · m and M2 = 7.5 N · m, respectively.

  How fast will it be going when it hits the ground

How fast will it be going when it hits the ground?

  Determine downstream depth into gradual contraction section

If the flowrate is Q = 25 ft^3/s and the upstream depth is 2 ft, determine the downstream depth. Sketch the specific energy diagram and indicate its important characteristics. Note that the specific discharges are different.

  Compute the flexural strerangth if the load is fracture

A three point bending test is performed on a glss specimen having a rectangular cross section of hight d =6 mm and width b = 12 mm the distance between support points is 45mm.

  Find the optimum number if technicians needed

A computer technician can handle on average 5 service calls per day. The cost of adding a technician (C1) is $200 per day and the estimated cost of waiting per incident (C2) is $250 per day.

  Determine that building solution complies with requirements

In accordance with BCA, what are the assessment methods and how may they be used to determine that a building solution complies with the performance requirements

  Determine the distance traveled by the cart comes to rest

The system is released from rest with no slack in the cable and the spring stretched 120 mm. The coefficient of kinetic friction between the 10 kg cart is 0.25 and the mass of block m is 6.3 kg.

  What is the dry unit weight the saturated unit weight

What is the dry unit weight, the saturated unit weight, and the buoyant unit weight, of a soil having a ratio of 0.5 and a value of Gs of 2.7

  Determine length of the cable between the pulleys a and b

Cylinders C and D are attached to the end of the cable. if D has a mass of 600 kg, determine the required mass of C, the maximum sag h of the cable, and the length of the cable between the pulleys A and B.

  Determine the landing speed of the airplane if it travels

A 32000 lb airplane lands on an aircraft carrier and is caught by an arresting cable. The cable is inextensible and is paid out at A and B from mechanisms located below deck and consisting of pistons moving in long oil-filled cylinders.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd