Determine the batch weights needed for all materials for

Assignment Help Civil Engineering
Reference no: EM13544574

Determine the batch weights needed for all materials for a 1yd^3 batch yielding an f'c= 2500 psi given the following information.

•slump = 5 inch max

•w/c = .55

•cementitious content = 675 lbs

•fly ash content= 30% by weight

•fly ash specific gravity= 2.8

•CA (limestone) specific gravity (SSD) = 2.578

• FA (sand) specific gravity (SSD) = 2.654

• cement( type 1) specific gravity = 3.14

•air content = 4% ( air entrained)

•coarse aggregate absorption = 2.4%

•coarse aggregate moisture content = 1.6%

•fine aggregate absorption= .8%

•fine aggregate moisture content = 2.8%

•58 % coarse aggregate

•42% fine aggregate

Reference no: EM13544574

Questions Cloud

What pressure must be provided at point 1 if you neglect : A pressure gage at elevation 4.8 m on the side of a storage tank containing oil reads 34.7 kPa.Another gage at elevation 2.2 m reads 57.5 kPa. Compute the specific weight, density, and specific gravity of the oil.
Find the steady-state concentration if the air is assumed to : Consider the air over a city to be a box 100 km on a side that reaches up to an altitude of 1.0 km. Clean air is blowing into the box along one of its sides with a speed of 4 m/s.
Suppose the utility encourages its customers to replace : Suppose a utility generates electricity with a 36 percent efficient coal-fired power plant emitting the legal limit of 0.6 lb of SO2 per million Btus of heat into the plant. Suppose the utility encourages its customers to replace their
What is the speed of the train relative to : The train is travelling at 0.8 m/s i relative to a man on the side of the tracks. What is the speed of the bug as seen by the man at the side of the tracks? What is the speed of the train relative to (or as seen by) the bug?
Determine the batch weights needed for all materials for : Determine the batch weights needed for all materials for a 1yd^3 batch yielding an f'c= 2500 psi given the following information.
What is the largest number of phases that can coexist at : Considering both temperature and pressure to be variables, what is the largest number of phases that can coexist at equilibrium in a binary alloy?
Calculate the volume of soil that will be needed if the void : A -4% grade and a 0% grade meeting at sta. 24 + 40 and elevation 2421.54 ft are joined by an 800-ft vertical curve. The curve passes under an overpass at sta. 25+00. If the lowest elevation of the overpass is 2439.93 ft, calculate the available clear..
Determine the stations and elevations of the bvc and evc : A 300 N force is applied at A as shown. Determine (a) the moment of the 300 N force about D, (b) the magnitude and sense of the horizontal force applied at C that creates the same moment about D, (c) the smallest force applied at C that creates the s..
What size pipe should we use to obtain a flow : Two large water reservoirs are connected by 8,000 ft of schedule 40 steel pipe. The level of one reservoir is 500 ft above the level of the other

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Determine what is the uncertainty in meters in the distance

A laser range finder consists of a laser and a light receiver. It operates by bouncing a laser pulse off a mirror and measuring the time of flight, the time it takes for the pulse to leave the laser, bounce off the mirror and return to the receive..

  Define mechanical engineering dynamics

Important information about Mechanical engineering dynamics, A 3000 lb car rests on a horizontal street out of gas with its brakes locked.

  Find the force in each of the rods neglect axial compression

a cantilever beam is additionally supported using two tierods. Both rods attach to the end of the beam. One rodcomes off at 45 degrees and attaches to the same wall that the beamis solidly fixed to

  Determine the maximum axial force p that can be applied

If the design speed of a multi-lane highway is 60 mph, what is the minimum sight distance that should be provided on the road if (a) the road is horizontal and (b) the road has a maximum grade of 5 percent? Assume the perception-reaction time = 2.5 s..

  Compute azimuths of all lines for aclosed traverse

Compute azimuths of all lines for aclosed traverse ABCDEFGHA that has the following balanced angles tothe right, using Bearing AB = N56º18'42"W.

  The lower surface is stationary and contains

Two infinite parallel horizontal surfaces are seprated by a film ofSAE 10W oil at T=10 C that is d=0.0144 in. thick . The uppersurface moves with speed V

  Which material will be cheaper if you want factor of safety

A structural tension member of 10 ft. long with a square cross-section is subjected to a load of 120,000 lb. There is a choice between an aluminum alloy and structural steel, with the following information given for each.

  What is ma the moment that tends to twist the telephone

An old wooden telephone pole with a single cross member was blown off center during a recent storm. To temporarily stabilize the telephone pole, a repair crew has attached a cable from the end of the cross member to an eye-ring stake anchored in t..

  The shortest distance in which the train can reach a speed

A monorail train starts from rest on a curve of radius 400 m and accelerates at the constant rate a_t. If the maximum total acceleration of the train must not exceed 1.5 m/s^2, determine

  Determine the number of gallons of paint needed to paint

Determine the number of gallons of paint needed to paint the outside surface of the water-supply tank, which consists of a hemispherical bottom, cylindrical sides, and a conical top. Each gallon of paint can cover 250 ft^2

  Find the find the force of cd and force acting at a and b

Draw the free-body diagram of member ABC which is supported by a smooth collar at A, rocker at B, and Find the Find the force of CD, and the force acting at point A & B

  What is the maximum grade this vehicle

A 2500-lb car (CD = 0.35, Af = 25 ft^2, and ? = 0.002378 slugs/ft^3) has 14-inch-radius wheels, a drivetrain efficiency of 90%, an overall gear reduction ratio of 3.2 to 1

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd