What is the minimum chain length for the application

Assignment Help Civil Engineering
Reference no: EM13563743

1.A soil deposit has a void ratio of 0.89, is the void ratio is reduced to 0.59 by compaction; find the percentage volume less due to compaction.

2.A motorcycle sprocket on the rear wheel has a diameter of 24 cm, and trhe driver sprocket has a diameter of 4.0 cm. The driver sprocket shaft and rear axle are 60 cm apart. What is the minimum chain length for the application.

Reference no: EM13563743

Questions Cloud

Determine the maximum velocity that the skier will achieve : A person with a mass of 200kg wearing snow skis is gliding down a long slope at an angle of 20 degrees. Each ski is 200cm long and 5 cm wide. The pressure of the skis on the snow melts a thin layer of water so that a .1mm layer of water exists under ..
What volume of naocl will be needed : If the plant uses sodium hypochlorite instead, what volume of NaOCl will be needed? Assume that the dry density of NaOCl is 1.2 kg/L and that 1 mg/L of dissolved NaOCl is equivalent to 1 mg/L of dissolved Cl2.
Derive an equation that would allow for direct calculation : A closed system of 0.123kg undergoes a frictionless, quasi-static process along the path PV=C from 100kpa to a final state where the volume is twice the initial volume. During the process 8140 N-m of work is done by the system. What is the final spec..
How long would you figure the soil will take to reach : An oil storage area, abandoned 10 years ago, had spilled oil on the ground and saturated the soil at a concentration of perhaps 400 mg/kg of soil. A fast food chain wants to build a restaurant there, and samples the soil for contaminants.
What is the minimum chain length for the application : A motorcycle sprocket on the rear wheel has a diameter of 24 cm, and trhe driver sprocket has a diameter of 4.0 cm. The driver sprocket shaft and rear axle are 60 cm apart. What is the minimum chain length for the application.
Determine the number of truck loads required to obtain : For construction of an embankment, the soil is transported from a borrowed area using a truck which carries 5.5 m^3 of soil at a time, with the following details: For the Borrowed Pit: bulk unit weight= 16 KN/m^3
Has the issue of having time not wasting become a parvasive : The plant manager has a decision to make. She needs to reduce the concentration of salt in the 8000- gallon tank from 30000 mg/L to 1000 mg/L. she can do it in one of two ways.
Prove that any polygon admits a triangulation : Prove that the smallest angle of any triangulation of a convex polygon whose vertices lie on a circle is the same. This implies that any completion of the Delaunay triangulation of a set of points maximizes the minimum angle.
What is the transistors emitter current : Ethane gas (C2H6) at 25C is burned with 150% theoretical air at 500 K and 1 atm. Find the heat transfer (in KJ/Kmol)from a steady-flow combustor if the products are at 1000 K and (a) complete combustion occurs; (b) 95% of the carbon is converted to C..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the concentration of pm in the stack

A stack (T=550*F and P=750mm Hg) was sampled using EPA Method 5. The total gas volume that flowed through the dry gas meter was 2.785 cubic meters (at T=60*F and P=800mm Hg). The mass of particles collected was 1.50g. Also, 72.0g of H2O was collected..

  Determine the tensile stress developed in member ab due

Air at 90 psia and 70 degrees F flows through a 4.5 inch diameter welded steel pipe (e = 0.00015) at 60 lb/min. Find the friction head loss and pressure drop in 200 ft of this pipe. Assume the air to be of constant density.

  Compute the station and elevation of the curve turning point

Set up a table showing curve elevations at the PVC, at the PVT, and at the half-station points along the curve. Compute the station and elevation of the curve turning point.

  Determine accelaration period in time

The 500- bed Lotta Hart Hospital has a small activated sludge plant to treat its wastewater. The average daily hospital discharge is 1200 L/day per bed

  Compute the max possible moment at the centerline

compute the max possible moment at the centerline of the beam and the absolute moment in the beam.

  Determine the angular velocity of link bc at the instant

If rod slides along the horizontal slot with a velocity of 44 ft/s , determine the angular velocity of link BC at the instant

  Determine which process requires more energy at atm pressure

Which process requires more energy: completely vaporizing 1 kg of saturated liquid water at 1 atm pressure or completely vaporizing 1 kg of saturated liquid water at 8 atm pressure

  Compute the critical load when the bar is subjected to an

A rectangular steel bar has cross-sectional dimensions of 12mm by 25mm and is 210 mm long. Assuming that the bar has pinned ends and is made from AISI 1141 OQT 1300 steel, compute the critical load when the bar is subjected to an axial compressive lo..

  Compute the critical depth and critical velocity for flow

A rectangle channel 20 feet wide carries a discharge Q= 200cfs. Compute the critical depth and critical velocity for the flow in the channel.

  Provide an equation that give an uncertainty of pressure

equation for pressure in bottom layer of a 2 layer fluid is: pressure,p =( specific weight of fluid 1,y1*thickness of fluid 1,h1) + ( specific weight of fluid 2,y2 * ( depth below the free surface at which the pressure is being determined, h - thi..

  Plot a curve showing the relationship of se versus

Plot a curve showing the relationship of Se versus L/r for steel columns. Draw the curve for slenderness ratios that vary from 0 to 200. Assume the proportional limit = 235 MPa

  Define which needs to be shafts minimum diameter

Assuming that the soil layers continue much beyond 60 feet in a similar pattern (obviously no landfill) in terms of friction and bearing capacities, recommend two different solutions that could allow the shafts to transmit their loads by 1) end be..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd