What is the maximum coefficient of road adhesion needed

Assignment Help Civil Engineering
Reference no: EM13544455

A rear-wheel-drive 3000-lb drag race car has a 200-inch wheelbase and a center of gravity 20 inches above the pavement and 140 inches behind the front axle. The owner wish to achieve an initial acceleration from rest of 15 ft/s^2 on a level paved surface. What is the maximum coefficient of road adhesion needed to achieve this acceleration? (Assume ?m =1.00.)

Step by step/required formula explanation needed.

Reference no: EM13544455

Questions Cloud

Determine the excess pressure inside an 0.5-in-diameter soap : Determine the excess pressure inside an 0.5-in-diameter soap bubble floating in air, given the surface tension of the soap solution is 0.0035 lb/ft.
What is the minimum distance that connects all the nodes : What is the minimum distance that connects all the nodes and what is the minimum possible time required for completing the  project?
What is the volume of this cloud in cubic miles : Calculate the volume (in ft^3) of a person of 180 lbf weight, assuming reasonable SG for the human body.
What is the maximum grade this vehicle : A 2500-lb car (CD = 0.35, Af = 25 ft^2, and ? = 0.002378 slugs/ft^3) has 14-inch-radius wheels, a drivetrain efficiency of 90%, an overall gear reduction ratio of 3.2 to 1
What is the maximum coefficient of road adhesion needed : A rear-wheel-drive 3000-lb drag race car has a 200-inch wheelbase and a center of gravity 20 inches above the pavement and 140 inches behind the front axle
What is the maximum shear stress in the liquid : If the viscosity of the liquid is 10–3 N-s/m2, what is the maximum shear stress in the liquid?
Determine graphically the magnitude and direction : The cable stays AB and AD help support pole AC. Knowing that the tension is 120 lb in AB and 40 lb in AD, determine graphically the magnitude and direction of the resultant of the forces exerted by the stays at A using (a) the parallelogram law, (b) ..
Calculate what is the frisbees rotational inertia : A 106g Frisbee is 18cm in diameter and has half its mass spread uniformly n the disk and the other half concentrated in the rim. What is the Frisbee's rotational inertia
Determine the maximum tension t that can be exerted : If a hook can sustain a maximum withdrawal force of 250 N inthe vertical direction, determine the maximum tension, T, that can be exerted.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the exit temperature through a tube at a rate

Water flows through a tube at a rate of 7.5 kg/min while heat is added to it at a rate of 4.5 kW. If water entered at 20 degrees celcius, determine the exit temperature. Assume the pressure remains constant at 1 atm throughout.

  Salary increases in engineering job are estimated

An enginnering student has just finished the freshman year and has received an offer of $20,000 per year in a full-time job, with prospects of salary increasing 3% per year until retirement after 33 years. If employement is taken, the student will li..

  A large part of holland is below sea level

A large part of Holland is below sea level.Earthen dikes keep the sea at bay. There's a Holland legend of aboy who uses his finger to plug a hole in the dike and saves thecountry side. Assume the center of the hole is located 3.0

  Determine what is the economic life of the challenger

The initial investment is $12,000 , there is no annual maintenance cost for the first 3 years , however , it will be $2,000 in each of years four and five , and then $4,500 in the sixth year and increasing by $2,500 each year thereafter .

  Influencing the allowable bearing pressure

What are the two principle factors influencing the allowable bearing pressure in the design of a specific footing- Are both of these factors equally important? Are both factors likely to be equally relevant for different soils types

  Determine what is the illumination on the note pad

A supervisor is sitting at her desk illuminated by a 180 candela source 3 feet above it. She is writing with green ink (reflectance=30%) on a yellow note pad (reflectance=60%). What is the illumination on the note pad

  Determine what is the speed of the ballast bag when it lands

A hot air balloon starting on the ground ascends at a rate of 12 km/hr and is carried by the wind (horizontally) at a rate of 20 kn/h. When the balloon reaches a height of 50 m, a ballast bag is dropped.

  What annual rate of return must the endowment fund earn

A permanent endowment at the University of Alabama is to award scholarships to engineering students. The awards are to be made beginning 5 years after the $10 million lump-sum donation is made.

  Determine the distance the engine is hoisted

The 3.5-Mg engine is suspended from a spreader beam having a negligible mass and is hoisted by a crane which exerts a force of 40 kN on the hoisting cable. Determine the distance the engine is hoisted in 2.4 s, starting from rest.

  Determine the rate of heat absorption for the outside air

Refrigerant 134a enters the condenser of a residential heat pump at 800 kPa and 35 degrees celcius at a rate of 0.018 kg/s and leaves at 800 kPa as a saturated liquid.

  Calculate the accumulated depreciation at the end of 4 years

An asset has an initial cost of $45,000 at the end of 4 years the salvage value of the asset is $5,000. Using the sum of the years' digits, calculate the accumulated depreciation at the end of the 4 years.

  Determinethe required diameter of the pin at joint b

A simple truss with joint detail is shown at the left. determinethe required diameter of the pin at joint B if a factor of safetyof 1.8 with respect to shear yielding is required, and the pn is tobe made of steel having shering stress of 145 MPa

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd