What is the volume of this cloud in cubic miles

Assignment Help Civil Engineering
Reference no: EM13544457

1.A person (mass of 80g) is lifted upward by a 2 cm diameter safety rope with constant velocity. What is the tensile stress in the rope?

2.Calculate the volume (in ft^3) of a person of 180 lbf weight, assuming reasonable SG for the human body. Show work

3.Clouds can weigh thousands of pounds due to their liquid water content. Often this content is measured g/m^3. Assume that a cumulus cloud occupies a volume of one cubic km, and its liquid water content is 0.2g/m^3.

a) What is the volume of this cloud in cubic miles?

b) How much does the water in the cloud weigh in pounds.

Reference no: EM13544457

Questions Cloud

Find the frictional resistance : A hydraulic lift of the type commonly used for greasing automobiles consists of a 10.000-in-diameter ram that slides in a 10.006-in-diameter cylinder, the annular space being filled
How could you use the family structural theory : How could you use the family structural theory to determine if a family is dysfunctional or not? Provide evidence to support your answer.
Determine the excess pressure inside an 0.5-in-diameter soap : Determine the excess pressure inside an 0.5-in-diameter soap bubble floating in air, given the surface tension of the soap solution is 0.0035 lb/ft.
What is the minimum distance that connects all the nodes : What is the minimum distance that connects all the nodes and what is the minimum possible time required for completing the  project?
What is the volume of this cloud in cubic miles : Calculate the volume (in ft^3) of a person of 180 lbf weight, assuming reasonable SG for the human body.
What is the maximum grade this vehicle : A 2500-lb car (CD = 0.35, Af = 25 ft^2, and ? = 0.002378 slugs/ft^3) has 14-inch-radius wheels, a drivetrain efficiency of 90%, an overall gear reduction ratio of 3.2 to 1
What is the maximum coefficient of road adhesion needed : A rear-wheel-drive 3000-lb drag race car has a 200-inch wheelbase and a center of gravity 20 inches above the pavement and 140 inches behind the front axle
What is the maximum shear stress in the liquid : If the viscosity of the liquid is 10–3 N-s/m2, what is the maximum shear stress in the liquid?
Determine graphically the magnitude and direction : The cable stays AB and AD help support pole AC. Knowing that the tension is 120 lb in AB and 40 lb in AD, determine graphically the magnitude and direction of the resultant of the forces exerted by the stays at A using (a) the parallelogram law, (b) ..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the torque that develops in the rod in in-lb

The end of a 0.75-in-diameter rod is fixed to an immovable plate. The length of the rod is 18.0 in. A 50-lb weight is attached to a 16.0-in lever at the end of the Rod so that the weight is hanging perpendicular to the longitudinal axis of the rod..

  How to calculate the ph of clean rain in the scenario

The pH of clean rain is influenced by the partial pressure of CO2 in the atmosphere. In addition, acid rain can be formed when sulfur dioxide (SO2) is discharged into the atmosphere. i) The atmospheric CO2 concentration could rise to 400 ppmv by 20..

  Purposes of assessing an economys growth performance

For the purposes of assessing an economy's growth performance, which is the more important statistic, real GDP or nominal GDP? Why?

  Determine factored uniform load per foot which beam supports

Structural steel beams are to be placed at 7ft 6in on center under a reinforced concrete floor slab. If they are to support a service dead load D=64 psf of floor area and a service live load L=100 psf of floor area

  Determine the maximum flexural stress in the rod

A steel rod of 1/8 inch diameter is bent into a loop 10 feet in diameter. Determine the maximum flexural stress in the rod.

  Determine the mass flow rate of the cooling water

refrigerant 134a is compressed at steady state from 2.4 bar, 0 degrees celcius, to 12 bar, 50 degrees celcius. Refrigerant enters the compressor with a volumetric flow rate of 0.38m^3/min, and the power input to the compressor is 2.6 kW.

  Calculate the mass and volumetric composition of 1 hcp

For a cement paste with an initial water-cement ratio of 0.5, by mass, calculate the mass and volumetric composition of 1 cm^3 of HCP under both wet and sealed curing conditions.

  Determine the flow rate per unit width of aquifer

The aquifer is inhomogeneous with K = 12+0.006x, where x =0 at point 1, and the piezometric heads at point 1 and 2 are 14.2 m and 18.8 m, respectively measured above the upper confining layer.

  Explain how to determine the particles velocity at s

acceleration of a particle traveling along straight line is a=(1/5)s^(1/2), s is in m, if v=0, s=3 when t=0 determine the particles velocity at s=6

  Find the internal forces as the nut is rotated 1 turn

A steel bolt and nut are tightened around an aluminum sleeve. Find the internal forces as the nut is rotated 1 turn

  Determine the vertical distance climbed

Neglecting the effect of altitude of local gravitional acceleration, determine the vertical distance climbed. Assume an average air density of 1.18 kg/m^3.

  A particle travels along a straight line with anbspvelocity

a particle travels along a straight line with anbspvelocity v 12-3t2 ms where t is in seconds.nbspwhen t 1 s the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd