Recommend installation of the orifice meter

Assignment Help Chemical Engineering
Reference no: EM131061400

The rate of flow of a liquid mixture is to be measured continuously. The flow rate will be approximately 40 gpm, and rates as low as 30 gpm or as high as 50 gpm can be expected. An orifice meter, a rotameter, and a venturi meter are available. On the basis of the following additional information, would you recommend installation of the orifice meter, the venturi meter, or the rotameter? Give reasons for your choice.

Density of liquid = 58 lb/ft3

Viscosity of liquid = 1.2 centipoises

Diameter of venturi throat = 1 in.

Upstream diameter of venturi opening = 2 in.

Manometers connected across the venturi and the orifice contain a non-miscible liquid (sp gr = 1.56) in contact with the liquid mixture

The maximum possible reading on these manometers is 15 in.

Orifice is square-edged with throat taps

Diameter of orifice opening = 1 in.

Diameter of upstream chamber for orifice meter = 3 in.

Calibration curve for rotameter is for water at 60°F and gives the following values:

2413_35836830-29f6-4a4a-a30b-75414c94c7f7.png

Reference no: EM131061400

Questions Cloud

Estimate the necessary wall thickness : estimate the necessary wall thickness. No corrosion allowance is necessary.
Interval captures the true population mean : For each of the sample means listed, use the standard error of10.23 to find a 95% confidence interval and state whether or not the interval captures the true population mean of 53.48 million dollars. (1) mean=40 (2) mean=70 (3) mean=84
Shape of the distribution of the number of books : (1) Using the mean and median given above, what is the likely shape of the distribution of the number of books read in a year? (2) Give the correct notation for the value "17". Is it a parameter or a statistic? (3) Give notation for and define the..
Explain the relationship between quality and productivity : Explain the relationship between quality and productivity. The text says that Toyota has focused on quality as its operations capability. Describe two (2) ways that Toyota's operations might have changed if it had focused on low cost instead of qua..
Recommend installation of the orifice meter : Manometers connected across the venturi and the orifice contain a non-miscible liquid (sp gr = 1.56) in contact with the liquid mixture
Determining the confidence intervals for the population mean : For a simple random sample of ten patients who have recently had knee surgery, the scores are as follows: 101, 92, 94, 88, 52, 93, 76, 84, 72, and 98. Construct and interpret the 90% and 95% confidence intervals for the population mean.
Problem regarding the statistical inference : A retailer believes that its new advertising strategy will increase sales. Previously, the mean spending in 15 categories of consumer items in both the 18-34 and 35+ age groups was $70.00. (For all hypothesis tests, assume the level of significanc..
Comparing the central tendencies : What conclusion can be derived by comparing the central tendencies of the two data sets?
What is the total filtering area required to deliver 30 ft3 : what is the total filtering area required to deliver 30 ft3 of filtrate in 1/2 h?

Reviews

Write a Review

Chemical Engineering Questions & Answers

  Solution of aluminum from a 5m stock of aluminum nitrate

Need to make 250 ml of a 0.100 M solution of aluminum from a 5M stock of aluminum nitrate. What do you do?

  Fit the data to an empirical heat-capacity equation

Fit the data to an empirical heat-capacity equation of the form by simple regression techniques.

  Concentration of the original lead

You decide to take 2.00 mL of the solution and add an excess of a concentrated sodium chloride solution. You obtain a solid with a mass of 3.407 g. What was the concentration of the original lead(II) nitrate solution?

  Excess pure oxygen and the flame temperature

Carbon monoxide (CO) is burnt in presence of 200% excess pure oxygen and the flame temperature achieved is 2298 K. The inlet streams are at 25 °C.

  Find the air fuel ratio for stoichiometric combustion

Find the air fuel ratio for stoichiometric combustion of Butane by volume. Calculate the percentage of carbon dioxide present in the DRY flue gas if 30% excess air is used

  Calculate the selectivity of ethylene for ethanol

A typical feed stream composition is 55% ethylene, 5% inserts, and 40% water. A typical product stream is 52.26% ethylene, 5.49% ethanol, 0.16% ether, 36.81% water, and 5.28% inserts. Calculate the selectivity of ethylene for ethanol and for ether..

  Alcohol technology 2 using the concept of a mass balance

using the concept of a mass balance describe how environmental engineers and scientists model the carbon cycle in the

  Calculate masses of alcohol and ether

Assuming that there are no other significant side reactions, calculate masses of alcohol and ether produced, per 1000 kg of allyl chloride fed to the reactor.

  Using the steam tables estimate cp

Using the steam tables estimate cp in (kj/kg k) , for super heated steam and  0.1 Mpas and 700deg  c

  How would you handle the response and how would you

upon responding to a 200 a.m. domestic transportation mishap your hazmat team determines that a liquefied compressed

  What is the drawdown

What is the drawdown at the perimeter of the well pumping 225 gpm when both wells are operating?

  Dielectric constant of water drop as a function

Why does the dielectric constant of water drop as a function of temperature?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd