Property rights along bodies of water vary from

Assignment Help Civil Engineering
Reference no: EM13536742

1) The accuracies that are achieved using kinematic surveying are sufficient for vertical control surveys (true or false)?

2)when relocating boundaries, the data given the highest preference of value are the bearings and distances (true or false)?

3)Property rights along bodies of water vary from the the thread of the stream to high water marks, and is based upon the navigability of the body of water and state law (true or false)?

4) When land area is decreased or increased by accretion or reliction, property boundaries are not changed,whereas boundaries are changed as the result of avulsion (true or false)?

Reference no: EM13536742

Questions Cloud

Find the inititial population : A 5 cm diameter, 6 m high pole is fixed in concrete. The pole supports a circular 4 m diameter sign. Estimate the maximum moment that must be resisted by the concrete for a wind speed of 30 m/s (wind is assumed normal to the sign; density of air = 1...
Find the tensions in both sides of the rope for someone walk : You are given that a piece of rope is 90.5 ft long. The distance between the poles holding the rope is 90 ft. We are to find the tensions in both sides of the rope for someone walking across the rope and the deflection
What are dtm and dem what is the difference between them : If the stage of a stream increases by 40% and the slope of the water surface becomes half of its original slope, then what will be changes in discharge of the stream?
Center of the instrument and the target and the elevation : Determine the horizontal distance, given:Stadia Top=8.5 ,Stadia Bottom 6.21, vertical angle= -8 degrees 42 minutes.
Property rights along bodies of water vary from : Property rights along bodies of water vary from the the thread of the stream to high water marks, and is based upon the navigability of the body of water and state law (true or false)?
Which the original 13 colonies were surveyed : Fixed GPS broadcast stations enable users to make differential measurements to other points whose positions are needed. In the US, there are two such networks two such networks of broadcast stations, name one (blank)
Imaging you have to shoot a basketball ball : Part B (Assignment): by trial and error, find the angle that will give the minimum force F to make a basket (hint: try 52 degrees)The trajectory of the ball will make a basket when x = L and y = Hb
How do you fill out the moment distribution : How do you fill out the moment distribution table? I dont know how to compute the values for each cell as the node is locked and un-locked.
Determine the largest magnitude of this force so that the : The cantilevered wild- flange steel beam is subjected to the concentrated force P at its end. Determine the largest magnitude of this force so that the bending stress developed at A does not exceed 180 MPa.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Estimate the time of submersion in years of the plate

Apiece of corroded steel plate was found in a submerged ocean vessel. it was estimated that the original area of the plate was 62.5cm 2 and approximately 2.8k had corroded away during the submersion.

  Determine force p in the coupling between trailer and truck

If the brakes are applied uniformly for 5 sec to bring the rig to a stop from a speed of 20 mph while moving down a 10 percent grade, determine the force P in the coupling between the trailer and the truck. The truck weighs 20,000 lbf and the trai..

  Environmental impact regarding the construction of the dam

Draw A flow net. Show flow lines, flow Channels, and Equipotential lines. Using flow nets, please provide an estimate of seepage rate below the dam. Your submittal will provide the basis for an environmental impact statement regarding the construc..

  Determine the length of the swale required from a catchment

A triangular shaped swale is to retain the runoff from a catchment with a design runoff rate of 0.01 m3/sec. The longitudinal slope of the swale is to be 1.5% with side slopes of 5:1 (H:V).

  How do you find the maximum axial load using asd

An 8x12 column of No. 1 Spruce-Pine-Fir(South) has an unbraced length for buckling about the strong x axis of 16 feet and an unbraced length for buckling about the weak y axis of 8 ft. Cm = 1.0 and Ct = 1.0

  Determine the minimum horsepower input to the pump

A pump delivers 60 degrees F water at 2000 gpm through a vertical pipeline 300 ft high. Find the minimum horsepower input to the pump. Assume that atmospheric pressure exists at both the pump inlet and the pipeline outlet.

  Draw a graph showing the effluent concentration as function

Draw a graph showing the effluent concentration as a function of time for : a. Zero order CMFR and PFR with the same influent concentration and reaction rate. b. First order CMFR and PFR with the same influent concentration and reaction rate.

  Determine to the nearest 1 by 4 in the smallest dimension h

If A and B are both made of wood and are 3/8 in thick, determine to the nearest ¼ in the smallest dimension h of the support so that the average shear stress does not exceed \tauallow = 300 psi.

  How far should a centerline extend past an object

1. What does the acronym ANSI stand for Stands for American National Standards Institute 2. What is the purpose of a titleblock The purpose of a title block is for give us enough information about the project.

  Determine the time needed for the velocity to become v

When a particle falls through the air, its initial acceleration a=g diminishes until it is zero, and thereafter it falls at a constant or terminal velocity v_f . If this variation of the acceleration can be expressed as a=(g/v^2_f)(v^2_f-v^2)

  Explain what design speed was used to design the curve

A freeway exit ramp has a single lane and consists entirely of a horizontal curve with a central angle of 90 degrees and a length of 628 ft. If the distance cleared from the centerline for sight distance is 19.4 ft

  Find the total length of pipe that must pass through furnace

The boiling water passes through copper pipes that have a wall thickness of 4 millimeters and a surface area of 0.12 square meters per meter length of the pipe. Find the total length of pipe (there are actually many pipes in parallel)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd