How do you fill out the moment distribution

Assignment Help Civil Engineering
Reference no: EM13536739

1) The earth is not a perfect sphere, but rather its shape is more accurately referred to as (blank).

2)(blank) is a term used in Geographic information Systems (GIS) to means reference particular positions on the earth's surface.

3) (blank) is the transformation of geographical data (latitude and longitude) on sphere or spheroid to a representative location of a flat surface.

4)(blank) stakes are currently used for grading operations for highways and railroads.

5.How do you fill out the moment distribution table? I dont know how to compute the values for each cell as the node is locked and un-locked.

Reference no: EM13536739

Questions Cloud

Center of the instrument and the target and the elevation : Determine the horizontal distance, given:Stadia Top=8.5 ,Stadia Bottom 6.21, vertical angle= -8 degrees 42 minutes.
Property rights along bodies of water vary from : Property rights along bodies of water vary from the the thread of the stream to high water marks, and is based upon the navigability of the body of water and state law (true or false)?
Which the original 13 colonies were surveyed : Fixed GPS broadcast stations enable users to make differential measurements to other points whose positions are needed. In the US, there are two such networks two such networks of broadcast stations, name one (blank)
Imaging you have to shoot a basketball ball : Part B (Assignment): by trial and error, find the angle that will give the minimum force F to make a basket (hint: try 52 degrees)The trajectory of the ball will make a basket when x = L and y = Hb
How do you fill out the moment distribution : How do you fill out the moment distribution table? I dont know how to compute the values for each cell as the node is locked and un-locked.
Determine the largest magnitude of this force so that the : The cantilevered wild- flange steel beam is subjected to the concentrated force P at its end. Determine the largest magnitude of this force so that the bending stress developed at A does not exceed 180 MPa.
Estimate the dimensions of the bio filter needed to treat : It has been reported that a peat biofilter treating styrene had a maximum elimination capacity of 100 g/m^3-hr,and a critical load of between 60-75 g/m^3-hr. Further investigation reveals that a 97% efficiency was acheived at a load 40 g/m^3-hr.
Find the concrete cross-section and steel area required : Find the concrete cross-section and steel area required for a simply supported rectangular beam with a span of 20 ft that is to carry a computed dead load of 1.3 k/ft and a service live load of 2.25 k/ft. Material strengths are fc’ = 5000 psi and fy ..
How far up the hill can she coast before coming to a stop : A cyclist is riding along a 25 mph and begins to coast just before encountering a hill with a 6% grade. How far up the hill can she coast before coming to a stop? Ignore air resistance and rolling friction.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the mass flow raw through the nozzle

Air enters an adiabatic nozzle steadily at 300 kPa, 200?C, and 30 m/s and leaves at 100 kPa and 180 m/s. The inlet area of the nozzle is 80 cm2. Determine (a) the mass flow raw through the nozzle, (b) the exit temperature of the air, and (c) the e..

  Bisection method to find the root of equation

Use the bisection method to find the root of the equation f(x) = x 2 - 4sin(x) = 0. For initial bracketing interval [a,b] , take a=1 and b = 3.

  What is the main difference of prestressed concrete beams

What is the main difference between the calculation of deflections for reinforced and prestressed concrete beams

  What is the 2-4-6-trichlorophenol concentration in ppm

A 500 L (132 gal) tank contains 255 mg/L 2,4,6-trichlorophenol dissolved in trichloroethylene (TCE). What is the 2,4,6-trichlorophenol concentration in ppm Assume the temperature of the system is 20 degrees C.

  Calculate the angular displacement for the pulley d

The cylinder B is released from rest. Determine the speed of both masses (vA and vB) after B moves by h m. Also calculate the angular displacement for the pulley D. The diameter of the pulley D is 0.2 m. Neglect all friction.

  What is the distiniction b/n point and non point sources

what is the distiniction b/n point and non point sources of water pollution and thier varation with surface and ground water?

  What is the ratio of the flow rates through the two pipes

Two long pipes convey water between two reservoirs whose water surfaces are at different elevations. One pipe has a diameter twice that of the other; both pipes have the same length and the same value of f.

  Find the absolute pressure when the barometer reads

determine the preassure in psi at a depth of 20 ft below the free surface of a body of water and find the absolute pressure when the barometer reads 29.9 inches of mercury.

  Will crack widths be affected by the air entrainment

Will crack widths be affected by the air entrainment?

  Find the centroid for the cone of ice cream

A single-scoop ice cream cone is a composite body made from a single scoop of ice cream placed into a cone. Assume that the scoop of ice cream is a sphere with radius = 3.36cm that is placed into a 9.90cm tall cone.

  Find the period of alternating vortices shed from boulder

Find the period of the alternating vortices shed from a boulder in a river under the following conditions: diameter of cylindrically-shaped boulder is 1 m; approach velocity is 1 m/s; water temperature is 15.6 C.

  Calculate the head loss at the beginning with a flow rate

An 8-inch water main with a flow rate of 14 ft3/sec raises 100-feet. At the beginning of the main the pressure is 110 psig and drops to 50-psig at the end. For this water main calculate the head loss

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd