Plot the shear and moment diagrams for the beam

Assignment Help Civil Engineering
Reference no: EM13563850

1.A particle moves along the positive x-axis with an acceleration in meters per second squared which increases linearly with x expressed in millimeters, as shown on the graph for an interval of its motion. If the velocity of the particle at x = 45 mm is 0.57 m/s, determine the velocity at x = 220 mm.

2.Given simply supported beam with an overhang. The beam is 12 inches wide by 24 inches deep, and the slab is 6 inches deep. use a roof live load of 20 psf, and a concrete density of 150 pdf. the beams are spaced 15 feet apart. the total beam length is 30 feet, with 24 feet between supports and a 6 foot overhang. plot the shear and moment diagrams for the beam

Reference no: EM13563850

Questions Cloud

Determine the gravitational force acting between two spheres : Determine the gravitational force acting between two spheres that are touching each other. The mass of each sphere is 400 kg and the radius is 300mm.
Determine the evaporation rate for a reservoir if the wind : Determine the evaporation rate for a reservoir if the wind speed is 40 mph and the surface temperature is 15 degrees Celsius and the overlaying temperature is 25 degrees Celsius. and the relative humidity is 30 percent
Determine the maximum value of the average : The frame shown consists of four wooden members, ABC, DEF, BE, and CF. Knowing that each member has a 2 3 4-in. rectangular cross section and that each pin has a 12 -in. diameter, determine the maximum value of the average normal stress (a) in member..
Determine the maximum negative moment in each span : A three span continuos beam has spans of 27, 30, 27 feet, total unfactored dead loads are 2,600 pounds per linear foot, unfactored live loads are 2,000 pounds per linear foot. For load combination 1.2D + 1.6L
Plot the shear and moment diagrams for the beam : Given simply supported beam with an overhang. The beam is 12 inches wide by 24 inches deep, and the slab is 6 inches deep. use a roof live load of 20 psf, and a concrete density of 150 pdf
How much sand did he place in the drum : A truck driver used sand to soak up a 1 g spill of lindane (C6H6Cl6). He placed the contaminated soil in an open drum which then filled with 150 L of water during a rainstorm. You test the water and find a concentration of 17 M.
What is the generic soil cleanup criteria for direct contact : Based on Michigan law, (a) what is the generic soil cleanup criteria for direct contact with residential soils contaminated with lead? Report your answer in units of "ppm" (
Calculate the water content and degree of saturation : A jet of water of diameter 75mm moving with a velocity of 25m/s strikes a fixed plates in such a way that the angle between the jet and plate is 60? find the force exerted by the jet on the plate. (a) In the direction normal to the plate and (b) In t..
The self resistance of a practical inductor : The self resistance of a practical inductor is (A) in series with the inductance. (B) in parallel with the inductance. (C) responsible for storing the magnetic energy. (D) No correct answer listed Capacitive reactance XC is:

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the compacted cubic yards per hour over 10-inch

Calculate the compacted cubic yards per hour if a compactor with a 5-ft drum width travels at 3 mph over a 10-in. lift of aggregate base course with 4 passes required to meet density specifications under average operating conditions.

  Compute azimuth of line pc to point p and chord distance

Given the stationing in meters as (4+56) for the PC of a horizontal curve of radius R=1200 meters and angle I=22°. The azimuth of the line PC to PI as AzPC-PI = 155° 30'. A point P is to be located on the curve at stationing of 7+00.

  With what velocity will air enter room under laboratory door

Laboratories containing dangerous materials are often kept at a pressure slightly less than ambient pressure so that contaminants can be discharged through an exhaust system rather than leaked through cracks and around doors to other parts of the ..

  Find max allowable force p for max allowable bearing

find the maximum allowable force P if the maximum allowable bearing stress on 6 pins holding 2plates together is σ all=10 MPa, and the maximum allowable shear stress is τ all =25 MPa

  Determine what were the size of the deposits

Uniform deposits were made on January 1 of 1991, 1992, 1993, and 1994 into a fund intended to provide $1000 on January 1 of 2005, 2006, and 2007. What were the size of these deposits

  What is the total equivalent future amount of the company

Vision Technologies Inc., is a small company that uses ultra-wideband technology to develop devices that can detect objects (including people) inside of buildings, behind walls, or below ground.

  Determine the specfic discharge and average linear velocity

The potentiometric surface elevations at two observation wells 1000 m apart are 52.35 m and 56.90 m. If the horizontal hydraulic conductivity of the auquifer is 25 m/ day determine the specfic discharge, and average linear veolicity of the flow as..

  Find length of shortest ladder that can stand outside wall

a tower is surrounded by a wall that is 10 m high and 30 m away from the base of the tower. compute the length of the shortest ladder that can stand outside the wall and lean against the tower.

  Find the axial load and the total change in each cross

A flat bar of cross section 20mm by 70mm elongates 4.0mm in a length of 2.0m as a result of axial load. If the elastic modulus is 199x106 kN/m2 and Poisson's ratio is 0.25 for the material, find the axial load and the total change in each cross secti..

  Determine the relationship between the discharge and the

A fluid of density rho flows steadily downward between the two vertical, infinite, parallel plates. The flow is fully developed and laminar. Make use of the Navier Stokes equation to.

  Find the average time in system

If the time required to pay for parking is exponentially distributed with a mean of 15 seconds, find the average time in system.

  Show that potential energy of the compressed gas is given

Let the cross - sectional area of the tube be given by A and the position of the cylinder by s , and assume that the compressed gas is an ideal gas at constant temperature so that the pressure P times the volume is a constant

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd