What is the generic soil cleanup criteria for direct contact

Assignment Help Civil Engineering
Reference no: EM13563848

Based on Michigan law, (a) what is the generic soil cleanup criteria for direct contact with residential soils contaminated with lead? Report your answer in units of "ppm" (b) what is the generic groundwater (residential and nonresidential ) cleanup criteria for residential drinking water contaminated with lead? Report your answer in units of ?g/L.

Reference no: EM13563848

Questions Cloud

Determine the maximum value of the average : The frame shown consists of four wooden members, ABC, DEF, BE, and CF. Knowing that each member has a 2 3 4-in. rectangular cross section and that each pin has a 12 -in. diameter, determine the maximum value of the average normal stress (a) in member..
Determine the maximum negative moment in each span : A three span continuos beam has spans of 27, 30, 27 feet, total unfactored dead loads are 2,600 pounds per linear foot, unfactored live loads are 2,000 pounds per linear foot. For load combination 1.2D + 1.6L
Plot the shear and moment diagrams for the beam : Given simply supported beam with an overhang. The beam is 12 inches wide by 24 inches deep, and the slab is 6 inches deep. use a roof live load of 20 psf, and a concrete density of 150 pdf
How much sand did he place in the drum : A truck driver used sand to soak up a 1 g spill of lindane (C6H6Cl6). He placed the contaminated soil in an open drum which then filled with 150 L of water during a rainstorm. You test the water and find a concentration of 17 M.
What is the generic soil cleanup criteria for direct contact : Based on Michigan law, (a) what is the generic soil cleanup criteria for direct contact with residential soils contaminated with lead? Report your answer in units of "ppm" (
Calculate the water content and degree of saturation : A jet of water of diameter 75mm moving with a velocity of 25m/s strikes a fixed plates in such a way that the angle between the jet and plate is 60? find the force exerted by the jet on the plate. (a) In the direction normal to the plate and (b) In t..
The self resistance of a practical inductor : The self resistance of a practical inductor is (A) in series with the inductance. (B) in parallel with the inductance. (C) responsible for storing the magnetic energy. (D) No correct answer listed Capacitive reactance XC is:
Calculate the depth of flow upstream of the bridge : Calculate the depth of flow upstream of the bridge assuming that the pier coefficient of drag is 1.2. Drag Force CD Af (V1^2)/2 CD=1.2
Determine the velocity of flow find the discharge in cfs : Given a V-shaped channel with a bottom slope of 0.001, a top width of 12ft, and a depth of 6 ft, determine the velocity of flow. Find the discharge in cfs and m^3/s.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Relevant materials properties

Whisker filaments of SiC that are 5 μm thick are coated withan aluminum alloy using a chemical bonding process. The coating process is carried out at 650 oC before the sample iscooled to room temperature

  How much energy in horsepower islost by the water while flow

A pipeline 1200ft long and 8in. in diameter hasat its inlet point 75ft of available hydraulic energy with respectto the reference level. The velocity in the pipe is 5fps; thepressure at its end is 12psi.

  Calculate the time till the smoke layer is from the floor

A room has a floor area of 500 m^2 and a height of 4 m. THe room is involved in a fire with a constant energy release rate of 1 MW. calculate the time till the smoke layer is 1.5 m from the floor for (a) the case where the leakage areas are at the ..

  Calculate flow velocities at each section of the pipe

A pipe carrying oil of specific gravity (SG = 0.877) changes in size from 150 mm at section E to 450 mm at section R (E and R are arbitrary designations of the two points in the system).

  Design the column including cross-sectional dimensions

A tied short column of square cross-section is subjected to a factored axial load of 2500 kN and a factored bending moment of 175 kN.m. Use a 40 mm clear cover to the ties and a 20 mm maximum aggregate size.

  Designing the tangent vertical curve

Due to a street crossing a roadway, the elevation of the roadway at station 3 +413.760 must be at 129.388 m. Design the curve?

  Find the weight and mass of the disk in us and si units

A disk is made of material having a SG = 8.3 and is 500 in diameter and a thickness of 10mm. Find the a) weight and b) mass of the disk in US and SI units.

  A cantilever beam is additionally supported using

A cantilever beam is additionally supported using two tierods. Both rods attach to the end of the beam. One rod comes off at 45 degrees and attaches

  What input of power rating is required for the pump

A water storage tank located on a larege dairy farm has a storage capacity of 0.1 ML. The average rate of water consumption from this tank is 6.25 kL per day, every day.

  If the required compaction is 95 percent of the target how

Base course aggregate has a target dry density of 119.7 lb/cu ft in place. It will be laid down and compacted in a rectangular street repair area of 2000 ft*48ft*6in. the aggregate in the stockpile contains

  Is it permissible to use darcys law under these circumstance

The water temperature is 14 C and the mean pore diameter is 0.33 mm. Is it permissible to use Darcy’s law under these circumstances? What is the reason for your answer?

  What is the lowest maximum cycle temperature at the engine

the pressure ratio across the compressor is 9 and the maximum temperature is 827c.the turbine and comprssor processes are adiabatic with turbine efficiency of 90% and a compressor efficiency of 85%.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd