Locate the well screen in the middle of the aquifer

Assignment Help Civil Engineering
Reference no: EM13542338

A well installed into a confined aquifer with a porosity of 0.3 and saturated thickness of 80 ft. The gravel pack requires a well screen slot width of 0.025 inches. The hydraulic conductivity of the aquifer is 60 ft/d. The radius of influence is 1200 ft and the hydraulic head at the radius of influence is 520 ft. The maximum permissible drawdown at the well is 25 ft. Determine the length of the well screen, the diameter of the well screen, the per cent open area of the well screen, the thickness of the gravel pack, the formation drawdown, the well screen drawdown, and the actual entrance velocity. The flow rate from the well should be greater than equal to 96000 ft^3/d. Locate the well screen in the middle of the aquifer formation.

Reference no: EM13542338

Questions Cloud

Calculate the sequent depth required to form a jump with : Assuming a drag coefficient Cd of 0.6 for the baffle blocks based on the upstream velocity and combined frontal area of the blocks, calculate the sequent depth required to form a jump with the blocks and compare this value to the sequent depth requir..
Determine the average shear stress in each pin : The pins on the frame at B and C each have a diameter of 0.25 in. If these pins are subjected to double shear, determine the average shear stress in each pin.
Should hole a be placed to make the net wind force zero : In strong winds the force can be quite large. Suppose that a hole is introduced in the building’s roof at point A to make pi equal to the surface pressure there. At what angle ? should hole A be placed to make the net wind force zero?
Determine the actual distance below the surface : In the determination of the average velocity of flow in wide rivers, it is common practice to estimate the average velocity in a vertical section by making a single measurement at a distance below
Locate the well screen in the middle of the aquifer : A well installed into a confined aquifer with a porosity of 0.3 and saturated thickness of 80 ft. The gravel pack requires a well screen slot width of 0.025 inches. The hydraulic conductivity of the aquifer is 60 ft/d. The radius of influence is 1200..
Find the conveyance of flow : A flow of 0.1 cum/s flows down in a rectangular channel of width of 0.6m and having and adjustable bottom slope. If chezys constant C is 56, determine the bottom slope necessary for uniform flow with a depth of flow 0.3m. Also find the conveyance of ..
Determine the increase in vertical stress at a depth of : A gunite concrete trapezoidal channel (n = 0.019) with 1:2 side slopes, as ilustrated below, conveys 60 m3/s on a slope of 0.0005. Compute the depth of flow.
The dynamic magnification of response compared : Detennine (1) the required shaker frequency to cause "resonance" and (2) the dynamic magnification ofresponse compared with static response for that level of damping.
Determine the deflection at the mid span of a simple : Determine the deflection at the mid span of a simple beam (wood joist) of a row house. The joist is designed as 2x12@16'' for DL = 12psf and LL=40 psf.

Reviews

Write a Review

Civil Engineering Questions & Answers

  State difference in bishop and fellenius method of slices

State the basic difference between the general method of slices and the bishop method of slices. b.)State the basic difference between the bishop and fellenius method of slices

  Find the speed of mass b for a given speed of mass a

A moves downward a distance of 3.6 ft, and mass B moves a distance x. What is the value of x 2. Find the speed of mass B for a given speed of mass A The system is released from rest and mass A moves downward at a constant speed of 8.0 ft/s.

  Determine if the heat pump is reversible or irreversible

If the heat pump requires a power input of 2 kW, and the room requires a heat input of 15 kW to maintain the temperature at 25°C, (a) find the COP of the heat pump. (b) Determine if the heat pump is reversible, irreversible, or impossible.

  Estimate the plume mass flow rate of a pool of benzene

A pool of benzene is ignited on the floor of a large industrial building. The total area covered by the Kerosene pool is 6 meters square (Note that this is considered a large pool D>0.2 meters). Combustion efficiency is 70%. Estimate the plume mas..

  Why do x components of reaction forces need to considered

Why do the X components of the reaction forces need to be considered when resolving the moment about point A

  Elevation and stationing of the low point

A 1600 ft long sag verical curve (equal tangent) has a pvc at station 1200+00 and elevation o 1500 ft. the initial grade is -3.5% and the final grade is 6.5%. determine the elevation and stationing of the low point, pvi and pvt.

  Determine what is the allowable torque of a circular tube

A circular tube has an outside diameter of 150mm and an inside diameter of 100mm. If the allowable shearing stress is 55MPa, what is the allowable torque

  Determine speed of the ball when it hits the bottom of lake

A ball is dropped from a boat so that it strikes the surface of a lake with a speed of 19.5ft/s. While in the water the ball experiences an acceleration of a = 10 - 0.8v, where a and v are expressed in ft/s^2 and ft/s, respectively

  What is the net cash inflow from the sale for situation a

A $125,000 tractor trailer is being depreciated by the Stright Line method over five years to a final Book Value of zero. Half year convention does not apply to this asset, After three years the rig is sold for A

  Calculate ph of buffer solution prepared by mixing water

Calculate the pH of a buffer solution prepared by mixing 8.5g KH2PO4 with 43.5g K2HPO4 in 1 liter of water (this is actually the composition of the dilution water used in a BOD test. Follow the same procedures you have been using for previous acid/..

  Determine the required area of the members

The truss is to be constructed of members with equal cross-sectional areas and using a material with yield stress 700 MPa. The structure must be designed to support a mass (m) of 3400 kg with a factor of safety of 3.

  Finding average time in system

If the time required to pay for parking is exponentially distributed with a mean of 15 seconds, find the average time in system.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd