Determine the deflection at the mid span of a simple

Assignment Help Civil Engineering
Reference no: EM13542334

Determine the deflection at the mid span of a simple beam (wood joist) of a row house. The joist is designed as 2x12@16'' for DL = 12psf and LL=40 psf.

The span length of the joist is 18'

spacing of joint is 16''

E = 1600 psi

joist is subjected to the uniform Load

DL= 16 lb/ft

LL= 53 lb/ft

Reference no: EM13542334

Questions Cloud

Locate the well screen in the middle of the aquifer : A well installed into a confined aquifer with a porosity of 0.3 and saturated thickness of 80 ft. The gravel pack requires a well screen slot width of 0.025 inches. The hydraulic conductivity of the aquifer is 60 ft/d. The radius of influence is 1200..
Find the conveyance of flow : A flow of 0.1 cum/s flows down in a rectangular channel of width of 0.6m and having and adjustable bottom slope. If chezys constant C is 56, determine the bottom slope necessary for uniform flow with a depth of flow 0.3m. Also find the conveyance of ..
Determine the increase in vertical stress at a depth of : A gunite concrete trapezoidal channel (n = 0.019) with 1:2 side slopes, as ilustrated below, conveys 60 m3/s on a slope of 0.0005. Compute the depth of flow.
The dynamic magnification of response compared : Detennine (1) the required shaker frequency to cause "resonance" and (2) the dynamic magnification ofresponse compared with static response for that level of damping.
Determine the deflection at the mid span of a simple : Determine the deflection at the mid span of a simple beam (wood joist) of a row house. The joist is designed as 2x12@16'' for DL = 12psf and LL=40 psf.
What is the critical state angle of friction of the soil : On a plane within a saturated soil mass, the total normal stress is 185 kPa, the pore-water pressure is 98 kPa and the shear stress is 42 kPa. The soil undergoes shear failure and reaches critical state on this plane
Find the depth and the rate of flow in si units for critical : Water flows down a wide and shallow rectangular channel of concrete (n=0.015) laid on a slope of 0.004. find the depth and the rate of flow in SI units for critical conditons in the channel.
Calculate the total vertical stress pore water pressure : An investigation at a particular site reveald 10 m of clay overlying 2m of sand resting on bedrock.the water table was found to be at the ground surface and the piezometric level for the sand to be 2m above ground level
What roughness coefficient would be required to produce : Evaporation rate in a 3650 acre-lake is 100 acre-ft/d. If inflow to the lake is 25.2 cfs, determine the change in storage (ft) during 365 days.

Reviews

Write a Review

Civil Engineering Questions & Answers

  How the public sees engineers

Discuss the differences between how engineers see themselves and how the public sees engineers

  Calculate the height of the model on the crest

The spillway section is 40 feet high, its crest length is 60 feet and the maximum discharge is 3,000 CFS when the head on the crest of the spillway is 5 feet. Using a model scale of 1:10, calculate the height of the model.

  Does stitching on ball have any influence on the trajectory

A baseball is hit from home plate and travels over the center field fence. What would the trajectory of the baseball look like if air-resistance was not factored in

  Estimate the diameter of the tower based on bottom operating

Estimate the diameter of the tower, based on bottom operating conditions. Assume that the density and viscosity of the bottom liquid are the same as tose for pure water. Make other appropriate assumptions as needed.

  Calculate the maximum temperature and maximum pressure

in an air standard otto cycle , the air at the beginning of the compression stroke is at 95 kpa and 22c ,and the cylinder volume is 0.0028 m^3 . the compression ratio is 9 and 4.3 kj are added during the heat addition process

  Determine the self weight moment of inertia

Determine the self weight, moment of inertia, and cross-sectional areas for the following hot rolled standard section:

  Estimate convective heat transfer coefficent for natural

Estimate the convective heat transfer coefficent for natural convenction from a horizontal steam pipe. The outside surface temperature of the insulated pipe is 80 degree C. The surrounding air temperature is 25 degress C.

  Determine what is local acceleration along the centerline

velocity of water in the nozzle is given by V=2t/(1-.5x/L)^2. L = 4ft. When x=.5L and t=3s what is the local acceleration along the centerline. What is the convective acceleration.

  Who has been offered a 5-year contract at a remote location

Suzanne is a recent chemical engineering graduate who has been offered a 5-year contract at a remote location. She has been offered two choices. The first is a fixed salary of $75,000 per year.

  A conical tube of length 8 m fixed vertically with its

a conical tube of length 8 m fixed vertically with its smaller end upwards. the velocity head and pressure head at

  Determine critical crack length to assure plate wont fail

A 1047 steel plate is subjected to a tensile stress of 120 MPa. Given its fracture toughness is 45 MPa?m and Y = 1, (a) Determine the critical crack length to assure the plate will not fail under static loading.

  What do you understand by the term durability compared to

1 what do you understand by the term durability? compared to other considerationsnbsphow much importance should be

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd