Find the depth and the rate of flow in si units for critical

Assignment Help Civil Engineering
Reference no: EM13542332

1.A rectangular channel 50 ft wide (n=0.015) carries a flow of 375 cfs. For the flow find the critical depth and critical velocity

2.Water flows down a wide and shallow rectangular channel of concrete (n=0.015) laid on a slope of 0.004. find the depth and the rate of flow in SI units for critical conditons in the channel.

3.The composition of a stream leaving a fermenter is 85.0 mol % water (H2O, MW = 18.01), 10.0 mole % ethanol (C2H5OH, MW = 46.07), and 5.0 mol % sucrose (C6H12O6, MW =180.16).

a) Calculate the stream composition weight %.

b) 850 lbm/h of the stream is fed to a purification process. 95% of the ethanol is recovered as product. Calculate the tons/year of recovered ethanol.

Reference no: EM13542332

Questions Cloud

Determine the increase in vertical stress at a depth of : A gunite concrete trapezoidal channel (n = 0.019) with 1:2 side slopes, as ilustrated below, conveys 60 m3/s on a slope of 0.0005. Compute the depth of flow.
The dynamic magnification of response compared : Detennine (1) the required shaker frequency to cause "resonance" and (2) the dynamic magnification ofresponse compared with static response for that level of damping.
Determine the deflection at the mid span of a simple : Determine the deflection at the mid span of a simple beam (wood joist) of a row house. The joist is designed as 2x12@16'' for DL = 12psf and LL=40 psf.
What is the critical state angle of friction of the soil : On a plane within a saturated soil mass, the total normal stress is 185 kPa, the pore-water pressure is 98 kPa and the shear stress is 42 kPa. The soil undergoes shear failure and reaches critical state on this plane
Find the depth and the rate of flow in si units for critical : Water flows down a wide and shallow rectangular channel of concrete (n=0.015) laid on a slope of 0.004. find the depth and the rate of flow in SI units for critical conditons in the channel.
Calculate the total vertical stress pore water pressure : An investigation at a particular site reveald 10 m of clay overlying 2m of sand resting on bedrock.the water table was found to be at the ground surface and the piezometric level for the sand to be 2m above ground level
What roughness coefficient would be required to produce : Evaporation rate in a 3650 acre-lake is 100 acre-ft/d. If inflow to the lake is 25.2 cfs, determine the change in storage (ft) during 365 days.
Calculate the molar flow rate for each component in each : The fermenter stream you saw for the last problem is to be separated by distillation as shown below. Its composition is 85.0 mol % water (H2O, MW = 18.01), 10.0 mole % ethanol (C2H5OH, MW = 46.07), and 5.0 mol % sucrose (C6H12O6, MW =180.16). Its tot..
What is the length of consecutive wet days that has : During the rainy season in a tropical country, the probability of a day being dry is 0.10. A dry day is defined as one without significant rainfall. Assuming that the number of days until the next dry day is geometrically distributed.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What fraction of the flue gas stream would need to be bypass

The company engineer decides that this is too good, that it is not necessary to be this efficient, and proposed that part of the flue gas be bypassed around the electrostatic precipitator so that the recovery of fly ash (particulates) from the flu..

  Determine the volume and density of the body

The volume and the average density of an irregularly shaped body are to be determined by using a spring scale. The body weighs 7200 N in air and 4790N in water. Determine the volume and density of the body.

  Determine the volume and mass of the liquid

A cylinder contains 3 kg of water and water vapor mixture in equilibrium at a pressure of 500 kN/m2. If the volume of the cylinder is 1.0 m3, calculate the following: a) Temperature of the mixture b) The volume and mass of the liquid

  Determine the curve elements-pc and pt stations

A horizontal curve on a two-lane highway is designed with a degree of curvature of 7 degree and a 50mph design speed. The coefficient of side friction for the design speed is 0.14. Deflection angle is 90 degree.

  Determine the components fa and fb along the oblique

Determine the components Fa and Fb of the 4.2 kN force along the oblique axes a and b. Determine the projections Pa and Pb of F onto the a- and b-axes.

  Derive the method-of-moments estimators for the parameters

Suppose an expert hypothesizes that the probability of a rainfall event causing a particular stormwater retention pond to overtop can be modeled with a beta (a, B ) distribution. Over n years of data collection, the percentages of rainfall events

  What flow rate of fresh water must be used to reduce salt

On the property they found a 20,000 m3 brine pond containing 25,000 mg/L of salt. The new owners propose to flush the pond into their discharge pipe leading to the Atlantic Ocean

  Determine horizontal and vertical components of the force

The window is to be bolted onto the vertical wall of the pool and faces outward, covering a 2ft diameter opening in the wall. The venter of the opening is 4ft below the surface.

  At what load would you expect the specimen to fracture

Three-point bending test was performed on an aluminum oxide specimen having a circular cross section of radius 5.5 mm; the specimen fractured at a load of 850 N when the distance between the support points was 50 mm.

  Determine the magnitude of reaction

Determine the magnitude of reaction at point A (in kips) of a 20' beam with 5kips at 4' of the beam and 2kips at 9' of the beam at 350lbs./ft.

  Select an economical hss 14 by 14 for the column

A steel column has a total unbraced height of 14 ft and carries an axial LRFD load of 950 kips. The column ends are fixed. Select an economical HSS 14x14 for this column.

  What is the mean velocity of air in the micro-channel

A micro-channel of diameter 0.5 mm and length 750 mm is connected to a plenum. A fan produces a negative gage pressure of -1.5 inch H2O in the plenum and draws air at 20oC into the micro- channel.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd