Is change in z dependent upon the specific weight or density

Assignment Help Civil Engineering
Reference no: EM13556979

If a large pool of water was rotating the same speed as an amusement ride, how far would the surface of the water rise, between the where the chairs are hanging when the ride stopped- which is 15ft from the center support column, and where the chairs are moving when the ride is operating- which is around 20ft from the center column. From prior experience, you estimate it will take 8 seconds to make a full revolution when the ride is operating.

In summary: Given r1: 15ft; r2: 20ft; w=2pi/8 rad/sec

a) Find: change in z (in feet) between the inner (r1) radius and outer (r2) radius.

b) Is change in z dependent upon the specific weight or density of the fluid?

Reference no: EM13556979

Questions Cloud

Evaluate the angular velocity of the platform with its load : A 91.3-kg horizontal circular platform rotates freely with no friction about its center at an initial angular velocity of 1.79 rad/s. Find the angular velocity of the platform with its load
Determine where the groundwater divide is located : In a water table aquifer bounded on the ends by rivers, the hydraulic conductivity is 50 m/day. The hydraulic heads at x = 0 and x = 1000 m are 100 m and 90 m, respectively.
Calculate how far from your friend are you : You and a friend are measuring a field for an ecology experiment. You walk due east at a speed of 0.9 m/s, how far from your friend are you
Does the density or specific weight of the water factor into : Assuming no friction losses in the hose, will the velocity change if the hose is draped over the handrail going around the pool instead of going under it?
Is change in z dependent upon the specific weight or density : If a large pool of water was rotating the same speed as an amusement ride, how far would the surface of the water rise, between the where the chairs are hanging when the ride stopped- which is 15ft from the center support column, and where the chairs..
A man says that the oil was reduced at a rate : An oil storage area abandoned 19 yrs ago had oil spilled on the ground and saturated the soil at a concentration of 400mg/kg of soil. A recent soil sample shows a concentration of 20mg/kg
Determine the emf induced in the second coil : A 2.64m -long coil containing 225 loops is wound on an iron core (average \mu = 1850\mu _0) along with a second coil of 115 loops. Determine the emf induced in the second coil
What is the highest possible design speed for this curve : You are asked to design a horizontal curve for a two-lane road. The road has 12-ft. lanes. Due to expansive excavation, it is determined that a maximum of 34 ft. can be cleared from the road's centerline toward the inside
Calculate the coefficient of permeability : A permeability test was run on a cylindrical soil sample with a length of 175 mm, and a diameter of 75 mm. After 90 seconds, discharge was 300 cm3 under constant head of 41 cm. The sample had a dry mass of 850 g and its ?s was 2.60 g/cm3. Calculate (..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the maximum shear force v of resisting

If the allowable shear stress is 100 MPa, calculate the maximum shear force V that a W460 X 60 structural steel wide flange is capable of resisting. Use the average web shear approach.

  What percentage is this loss reduced if the provision

Water leaves a turbine at 18.5 fps and enters a tailrace having an average velocity of 1.5 fps. What is the submerged discharge head loss? By what percentage is this loss reduced if the provision of a draft tube increases the discharge flow area to s..

  Calculate the gradient under which the flow is occurring

The relative density of a sloped sand deposit is known to be 75%. Water is observed to be seeped through this slope at a rate such that the discharge velocity is 0.6 m/day. If the hydraulic conductivity for this deposit is 4×10-4 m/s.

  Derive an expression for small flow rates over a spillway

Derive an expression for small flow rates over a spillway, in the form of a function including dimensionless quantities. Use dimensional analysis with the following parameters

  Find the flow rate if the pump puts 22 hp in to the flow

A 110 f t long, 5 in in diameter (f = 0:033) connects two reservoir whose water surface elevations differ by 12 f t. Compute flow rate in pipe.

  Determine the max static stress the component must sustain

With a safety factor of two on the time, determine the maximum static stress the component must sustain in order to have a service life of 10000 hours.

  Determine the angular acceleration of the spool

determine the angular acceleration of the spool and the acceleration of the trailer. The wheels have negligible mass and are free to rotate.

  Find the mean value of the time rate of change of the

Gas is flowing in a long 9-in-diameter pipe from A to B. At sectionA the flow is 0.65 lb/sec while at the same instant at section Bthe flow is 0.72 lb/sec. The distance between A and B is 750 ft.

  Find the direction of flow

A conical tube of length 8 m fixed vertically with its smaller end upwards. The velocity head and pressure head at upper ends are 1.27 m and 2.50 m respectively. The velocity head and pressure head at lower ends are 0.203 m and 5.407 m respectivel..

  Commencement of fill placement

Determine the horizontal spacing of the vertical drains if the drains are installed in triangular grid to reach 90% of primary consolidation in 1.5 years after the commencement of fill placement.

  What is the airflow rate needed to maintain the skirts

A design for a hovercraft is made. A fan sends air in from the top of the rectangular chamber (60F) and is exhausted between skirts and the ground. Pressure in the chamber is responsible for lift, and the craft is 15 by 7 ft.

  What is bod5 using a mix consisting of four parts

A standard five-day BOD test is run using a mix consisting of four parts distilled water and one part wastewater (no seed) the initial DO of the mix is 9.0 mg/l , and the do after Five days, determined to be 1.0mg/l. what is BOD5

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd