Give one reason why this should be considered by management

Assignment Help Civil Engineering
Reference no: EM13563751

A chemical plant produces a process wastewater that contains a relatively high concentration of a small number of nontoxic organic compounds, but very low concentrations of solids or salts. It has no odor. A junior engineer suggests that it could be used to flush toilets and rinse process vessels before being treated for discharge into the municipal sewer system. Because there are few restrooms in the plant, the cost of plumbing would be relatively small. Give one reason why this should be considered by management and one reason why it should not be considered.

Reference no: EM13563751

Questions Cloud

How much delay can be reduced by your strategy : There exists one more intersection at downstream location, which is away 300m from the first intersection. If this intersection has traffic signal with same cycle time, draw queueing diagram for the second intersection, and find optimal traffic signa..
What would be the fraction of trucks entering the section : Consider a highway section where traffic is stationary, all trucks travel at speed s and cars at speed v. If aerial surveillance revealed that trucks were a fraction p of the vehicles on a photograph, what would be the fraction of trucks entering the..
What steady-state concentration of co will be observed : A person may demonstrate observable effects on the central nervous system when exposed to carbon monoxide at a concentration of 50 ppm, may lose consciousness at a concentration of 250 ppm, and may die at a concentration of 750 ppm. A "typical" urban..
Determine the ph of water in a closed calcium carbonate : Determine the pH of water in a closed Calcium Carbonate Aquifer. Assume that the temperature is again 25oC, and that the aquifer material is pure Calcium Carbonate. Again you must list all species that exist in the system and all equations.
Give one reason why this should be considered by management : A chemical plant produces a process wastewater that contains a relatively high concentration of a small number of nontoxic organic compounds, but very low concentrations of solids or salts.
How long will it take to concentrate the solution : 150,000 mol of aqueous phosphoric acid (H3PO4) solution contains 5.00% H3PO4 by moles. The solution is concentrated by adding pure H3PO4 at a rate of 20.0 L/min.
Calculate the pressure and mole fractions in the vapor : Water is used in a heat exchange to cool 5 kg/s of air from 400 C to 200 C. Calculate (a) the minimum mass flux (kg/s) of the water and (b) the quantity of heat transferred (MJ) to the water each second. The water enters at 20 C and leave at 30 C.
Balance the latitudes and departures by using the compass : A four-sided closed field traverse has the following angles. A = 81 degrees 22%u201930%u201D, B = 72 degrees 32%u201930%u201D, C = 89 degrees 39%u201930%u201D, D =116 degrees 23%u201930%u201D.
Determine the maximum velocity that the skier will achieve : A person with a mass of 200kg wearing snow skis is gliding down a long slope at an angle of 20 degrees. Each ski is 200cm long and 5 cm wide. The pressure of the skis on the snow melts a thin layer of water so that a .1mm layer of water exists under ..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Draw the shear and bending moment diagrams for the beam

The beam ABC of length L has two different moments of inertia (2I in AB, I in BC) and a constant elastic modulus E. It is fixed at point A has a roller support at point B and a load P at C. a. Sketch the deflected shape of this beam.

  Determine how many balloons would be taken

To float a 160 pound man using helium balloons (assume 0.52 cubic feet per inflated balloon). How many balloons would it take. Assume density of air is 1.29 kg/cubic meter and the density of helium is 0.179 kg/cubic meter.

  Estimate the tensile strength and the modulus of elasticity

The concrete cylinder 6 in x 12 in broke incompression at a load of 110000 lbs. Compute the crushing strength of concrete. Estimate the tensile strength and the modulus of elasticity.

  Explain how and why the rotational restraint at top of wall

The design of a masonry wall to support vertical compression loading is influenced by the same factors that affect the design of all compression elements. One of these factors is the extent of rotational restraint at the top of the wall.

  How to calculate the depth of a masonry dam

How to calculate the depth of a masonry dam of trapezoidal cross section with height of 24ft,2ft top width,,12 ft base width and weight of concrete 150 lb/ft^3.

  What force vector does the angled member apply

The linkage shown is made up of two 3-kg rectangular members (0.4 m by 0.1 m), and is flying through the air. At the instant shown, the vertical member has angular velocity 4 rad/s, and the angled member has angular velocity 1 rad/s.

  Determine the spiral curve length to satisfy all requirement

A horizontal curve on a two-lane highway is designed with a 818.51ft radius, 12ft lane, superelevation 6.4%, and a 50mph design speed. Deflection angle is 90 degree. The maximum relative gradient is 0.50.

  How many feet of head must the pump add to achieve

At a pumped storage facility, water is pumped from a large reservoir to a point 150 feet above the resevoir. How many feet of head must the pump add to achieve

  Determine the velocity of slider block

Knowing that at t= 3s slider block C has moved 57 mm to the right, Determine the velocity of slider block C at t=0, (b) the acceleration of A and C, (c) the change in position of block A after 5s.

  How can utah and other parts of the country

how can Utah and other parts of the country have the same temperature but a different humidity?

  Determine the initial weight and final density of the water

A steel tank hold 120 ft^3 of water at atmospheric pressure(14.7psi and 68.4 degrees f). the water is subjected to a 100 fold increase in pressure. determine the initial weight and final density of the water if the volume decreases by .545 ft ^3.

  Determine if the as-drawn wire will break during the process

A 3105 Aluminum alloy wire is to be drawn to give a 1-mm diameter wire having a yield strength of 20,000 PSI. assume that there is no friction in the wire drawing process

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd