Find the z components of the electric field

Assignment Help Civil Engineering
Reference no: EM13548149

An electron has an initial velocity with an x component of zero, a y component of 9.35 km/s, a z component 16.1 km/s, and a constant acceleration of 1.60 x 1012 m/s2 in the positive x direction in a region in which uniform electric and magnetic fields are present. If the magnetic field has a magnitude of 428 µT and is in the positive x direction, find the

(a)x,

(b)y, and

(c)z components of the electric field. Give your answers in V/m

Reference no: EM13548149

Questions Cloud

Find the flow rate if the pump puts 22 hp in to the flow : A 110 f t long, 5 in in diameter (f = 0:033) connects two reservoir whose water surface elevations differ by 12 f t. Compute flow rate in pipe.
Express the approximate alkalinity of this water as mg : A water sample has bucarbonate concentration of 220 mg/l ( HCO3- )and the PH of the water is 7.9 > Express the approximate alkalinityof this water as mg/l of CaCO3
Find all contact forces : Cylinders A & B weigh 500N each and cylinder C weighs 1000N. Assuming frictionless contact between all surfaces, find all contact forces. Diameters A&B= 1, C=2
Calculated the change in vertical effective stress on the : A culvert is to be constructed in a bed of sand (e = 0.5) for drainage purposes. The foof of the culvert will be located 3 m below ground surface. Currently the groundwater level is at ground surface.
Find the z components of the electric field : An electron has an initial velocity with an x component of zero, a y component of 9.35 km/s, a z component 16.1 km/s, and a constant acceleration of 1.60 x 1012 m/s2 in the positive x direction in a region in which uniform
What is the probability that the maximum wind pressure will : A large parabolic antenna is designed against wind load. During a wind storm, the maximum wind-induced pressure on the antenna, P, is computed as P= 1/2CRV^2 Where C = drag coefficient, R = air mass density in slugs/ft3, V = maximum wind speed in ft/..
Determine the stretch of the cord when the system : The two disks each have a mass of 25kg and are attached at their centers by an elastic cord that has a stiffness of k = 1.6kN/m . Determine the stretch of the cord when the system is in equilibrium
Discuss the minimum alignment required to establish the : Explain the process for establishing a centerline for a roadway for an existing road. Include a description of the types of property markers used as well as any problems a surveyor may encounter in this process
Calculate the force in each member of the loaded truss : List the series of steps involved in converting rural land into development. You may refer to an example of local conditions in your reference jurisdiction or you may use a description of such steps that you find from other sources, but do not limit ..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the required area of an air to air heat exchange

Calculate the required area of an air to air heat exchange to cool 20,000 cfm from 1200 F to 400 F. Assume ambient air at 80 F will be heated to 800 F by the exchange. Assume heat losses are 10 % and that the overall heat transfer coefficient is 1.0 ..

  Calculate what is the peak discharge at the reach outlet

Use the Muskingum method to route a flood through a reach a river. The base flow is 100 cfs, and the incoming flood flow increases 50 cfs every 2 hr over a 6 hr period and the subsides at the same rate.

  What is the rolling resistance

He is concerned about the high rolling resistance of the units in the sand (RR factor 250lb/ton).  What is the rolling resistance?

  If the required compaction is 95 percent of the target how

Base course aggregate has a target dry density of 119.7 lb/cu ft in place. It will be laid down and compacted in a rectangular street repair area of 2000 ft*48ft*6in. the aggregate in the stockpile contains

  Determine the maximum tensil and compressive stresses

the vertical portion of the press shown below consists of rectangle tube of wall thickness t=8mm. knowing that the press has been tightened on wooden planks being glues together until P = 20 kN,

  Show by counter example that if f isnot onto then

Suppose that F1 ο G2 =F1ο G1 then F : S→ T, G1 : T → U, G2 :T →U,. Define a function F : R2 ? R2 by F(x, y) = (x +y, x - y). . Show that if F is onto, Suppose that G1ο F = G2 ο F.

  The chord length is 6ft and the wingspan

An airplane with a Clark Y airfoil cross-section weighs 3500 lbs. The chord length is 6ft and the wingspan is 36 ft. Determine the: a) Minimum speed and power to take off, if the angle of attack is 12.4 degrees.

  Write a program that processes a sequence of lines

Write a program that processes a sequence of lines from a file, displaying a count of the total number of words in those lines as well as counts of words with one letter two letters,and so on.

  Determine theoretical maximum efficiency of the heat engine

Assume the collector provides this energy to a thermal storage unit (a thermal reservoir) at 220oC. A heat engine receives energy from this thermal storage unit and discharges energy by heat transfer to the surroundings at 20 C

  Determine the critical load of a steel tube

Determine the critical load of a steel tube that is 5 m long and has a 100-mm outer diameter and a 16-mm wall thickness. Use E = 200 GPa.

  What is the elevation of the curve at station of the pvi

An equal-tangent crest curve connects a +2% initial grade with a -1% final grade, and is designed for 55 mi/h. The station of the PVI is 233 + 40 with elevation 1203 ft.

  Which would be the strongest and highest bmelting point

explain how mechanical strength, melting temperature , and thermal exapntion are related at the atomic level. specifically, how do they relate to each other and the bonding energy between the atoms.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd