Determine what is the value of degree for the sand

Assignment Help Civil Engineering
Reference no: EM13310575

A square footing 0.3 m by 0.3 m is placed on the surface of a dense cohesionless sand (unit weight = 18.2 KN/m^3) and subjected to a load test. If the footing fails at a load of 13.8 KN, what is the value of (degree) for the sand?

Reference no: EM13310575

Questions Cloud

Determine what is the maximum flow rate that can be pumped : assume the pipe diameter is 4-inches, (f = 0.035), Distance from BC is 15-feet, distance DE is 180-feet and z = 60-feet. The elevation of C is 10-feet above the lower water surface.
Determine what is the modulus of rupture of wood : A flexure test is done to determine the modulus of rupture of wood. Given that a=15in, L=34in, and the maximum load P that was applied was 5950lbf, what is the modulus of rupture of wood
Explain styrene is produced by catalytic dehydrogenation : Styrene is produced by catalytic dehydrogenation of ethylbenzene at high temperature in the presence of superheated steam. A.) Given the following data, what is the delta Hrxn, delta Grxn and delta Srxn at 298 K
How many lines per cm does the grating have : Sodium light of wavelength 589nm falls on a diffraction grating and its first-order peak on a screen 60.0cm away falls 3.32cm from the central peak. How many lines per cm does the grating have
Determine what is the value of degree for the sand : A square footing 0.3 m by 0.3 m is placed on the surface of a dense cohesionless sand (unit weight = 18.2 KN/m^3) and subjected to a load test. If the footing fails at a load of 13.8 KN, what is the value of (degree) for the sand
Discuss roger''s duties as a director : Discuss Roger's duties as a director and any defenses he has to the lawsuit.
What is the thickness of the film : A thin film of alcohol (n=1.36) lies on a flat glass plate (n=1.51). When monochromatic light is incident normally on the system, What is the thickness of the film
Determine what is the stationing and elevation of the pvc : A vertical curve is designed for 55 mi/h and has aninitial grade of +2.5% and a final grade of 1.0%. The PVT is at station 114 + 50. It is known that a point onthe curve at station 112 + 35 is at elevation 245 ft.
Evaluate delta g at 298 k for the formation : High levels of ozone (O3) make rubber deteriorate, green plants turn brown, and cause people to have difficulty breathing. Calculate delta G at 298 K for the formation of 1 mole of O3 from O2 in urban smog, where [O2]=0.210 atm and [O3]=5.00x10^-7..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine how much runoff reached the river for the year

The average rate of flow measured in a gage at the outlet of the watershed was 30 m^3/sec. Estimate the water losses due to the combined effects of evaporation, transpiration, and infiltration due to ground water.

  Find area of steel reinforcement required for concrete tbeam

Find the area of steel reinforcement required for a concrete T-beam for the following data; f'c = 3 ksi, fy=60 ksi,d=18 in, t= 4.5 in., bw= 10 in., bf= 36 in., 3/4" aggregate, and the section sustains a total factored bending moment 82 k-ft.

  Shear and bending moment expressions

Show or formulate the shear and bending moment expressions for each board, and plot/draw the shear and bending moment diagrams of the boards.

  Calculate average gas temperature in upper layre of room

A steady fire with an energy release rate of 500 kW occurs in a room 3m wide, 3m long, and 2.4 m high, with a door opening which is 1.8 m high and 0.6m wide. the ambient temperature is 20 degree celcius.

  Determine the change inside diameter when the gun is fired

a navel gun (E= 30,000 ksi and G = 11,600 ksi) with a bore of 16 in. develops a maximum internal pressure of 20,000 psi. Determine a. the minimum outside diameter required if the maximum tensile stress permitted in the gun barrel is 36,000 psi.

  Determine the peak discharge that would result no ponds

Suppose a drainage basin has an area of 288 acres with a CN=55(Runoff Coef. of 0.30). Determine the peak discharge (in cfs) that would result from a 6.0in., 24-hr assuming there are no ponds and swampy areas.

  Define energy transfer in mechanical systems

Energy transfer in mechanical systems, A wheel is 800mm in diamiter and has a mass of 1000kg. on a horizontal surface without skidding, the vehicle accelerates uniformly at 0.5m/s^2 for 5 seconds.

  Supporting Investment Promotion: ERNST & YOUNG

Ernst & young is currently providing support to various sectors. In this regards it was felt that if this report is able to document good practices currently being adopted or planned in ceramic sector.

  Determine the elevation of the lowest point of the curve

A 400ft equal-tangent sag vertical curve has its PVC at station 200 + 00 and elevation 250ft. The initial grade is -5.0% and the final grade is +2.5%. Determine the elevation of the lowest point of the curve.

  Determine the reaction forces at points b and c

The fixture AC is designed with a screw adjustment to regulate the height of the 900 N load supported by the roller at A. The screw bears against a smooth surface at B. Determine the reaction forces at points B and C. Neglect the weight of the fix..

  Determine what is the temperature in the tire after driving

The temperature when the tires were in flated was 25 F. Assuming no change in air mass or volume, what is the temperature (F) in the tire after driving yesterday is a pressure on 44 psig was measured

  Will the pce standard of 5 microgram per l be exceeded

If an 18.9 L (5 gallon) bucket of PCE is released (and equally distributed) into a 3.79x10^8 L (100,000,000-gallon) aquifer, will the PCE standard of 5 microgram/L under the Safe Drinking Water Act be exceeded

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd