Determine what is the maximum flow rate that can be pumped

Assignment Help Civil Engineering
Reference no: EM13310579

assume the pipe diameter is 4-inches, (f = 0.035), Distance from BC is 15-feet, distance DE is 180-feet and z = 60-feet. The elevation of C is 10-feet above the lower water surface. If the pressure head @ C is to be no less than (-) 20 feet, what is the maximum flow rate that can be pumped? Flow rate in CFS

Reference no: EM13310579

Questions Cloud

Which two reactions are occuring at the anode and cathode : Which of the following is true for a thermistor with a negative temperature characteristic A) Decreasing temperature produces decreasing resistance in the thermistor. B) Increasing temperature produces decreasing resistance in the thermistor.
United states are allergic to one or more food ingredients : When composing business messages, how can you communicate with an authentic voice and project your company's image at the same time? [
Find the kinetic energy attained by the system : A uniform disk of mass .53kg and radius 11cm is constrained to rotate on an axis about its center. find the KE attained by the system
Explain hcl are added assuming no change in volume : A 500ml Buffer solutin is 0.150 M in HNO2 and 0.175 M in KNO2. The Ka for HNO2 is 4.6*10^-4. What is the inital pH of this buffer. What is the pH of the buffer in the question above if 0.0049 moles of HCl are added assuming no change in volume
Determine what is the maximum flow rate that can be pumped : assume the pipe diameter is 4-inches, (f = 0.035), Distance from BC is 15-feet, distance DE is 180-feet and z = 60-feet. The elevation of C is 10-feet above the lower water surface.
Determine what is the modulus of rupture of wood : A flexure test is done to determine the modulus of rupture of wood. Given that a=15in, L=34in, and the maximum load P that was applied was 5950lbf, what is the modulus of rupture of wood
Explain styrene is produced by catalytic dehydrogenation : Styrene is produced by catalytic dehydrogenation of ethylbenzene at high temperature in the presence of superheated steam. A.) Given the following data, what is the delta Hrxn, delta Grxn and delta Srxn at 298 K
How many lines per cm does the grating have : Sodium light of wavelength 589nm falls on a diffraction grating and its first-order peak on a screen 60.0cm away falls 3.32cm from the central peak. How many lines per cm does the grating have
Determine what is the value of degree for the sand : A square footing 0.3 m by 0.3 m is placed on the surface of a dense cohesionless sand (unit weight = 18.2 KN/m^3) and subjected to a load test. If the footing fails at a load of 13.8 KN, what is the value of (degree) for the sand

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Determine the planer density and packing faction for fcc

determine the planer density and packing faction for FCC nickel in (100), (110), and (111 planes. which, if any, of these planes is close-packed

  What is the total delay per cycle and delay per vehicle

A left-turn movement has a maximum arrival rate of 200 veh/h. The saturation flow of this movement is 1400 veh/h. For this approach, the yellow time is 4 seconds, all red time is 2 seconds and total lost time is 3 seconds.

  What is the value of x when block comes to rest momentarily

The block is released from rest when the spring is unstretched (at x=0). We wish to show that the ensuing motion of the block is simple harmonic. Call the initial configuration of the system that existing just as the block is released from rest.

  What is elevation of b by neglecting curvature and reaction

The line of sight of a level falls at a rate if 0.122ft/ 100 ft when the level bubble is centered. A backsight of 4.782 is taken on point A, which is at 75 ft from the level. the elevation of a is 425.238 ft.

  Explain how to determine the power output of the turbine

The water enters at 1 atm at 10 C and the flow rate through the turbine is 40 m3/s. The water is discharged from the turbine 200 m below the intake at 1 atm and the temperature of the water at the discharge is 10.2 C.

  Calculate the molar mass of the biomolecule

A 2.50-g sample of a large biomolecule was dissolved in 13.0 g of carbon tetrachloride. The boiling point of this solution was determined to be 77.85°C. Calculate the molar mass of the biomolecule.

  Determine the normal and shear stresses acting on an angle

A pressurized steel tank has a radius r=0.6m, a wall thickness t=18mm and an internal pressure p of 2.8 MPa.The steel has a modulus of elasticity E of 200 GP and a poissons ratio 0.30.

  Determine the principal stresses and the principal angle

using the stress transformation quations only,given a stress state where sigma x=6500 psi,sigma y= 17,300 psi and tau xy=2900 psi, determine the principal stresses,the principal angle and the maximum shear stress.

  What pressure in psi is applied to water to reduce volume

At normal atmospheric conditions, approximately what pressure in psi must be applied to water 70 F to reduce its volume by 2 %

  What will be the mass of the rod at the end of 20 mins

A common commercial process for the production of so-called "Electronic Grade Silicon" (EGS) is the Siemens process (see figure below). EGS is of ultra-high purity, enough to be used for fabrication of microchips.

  What must the ph be raised to in order to precipitate

Groundwater in Taupe, Arizona, initially contains 1.8 mg/L of iron(III). What must the pH be raised to in order to precipitate 0.3 mg/L of the iron (T=25°C)

  Determine the maximum bending stress on the outside surface

A concentrated moment is applied to the free end. Determine the maximum bending stress on the outside surface of the cylinder and the maximum bending stress on the inside surface of the cylinder.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd