Determine the tensile stress developed in member ab due

Assignment Help Civil Engineering
Reference no: EM13543413

1.Air at 90 psia and 70 degrees F flows through a 4.5 inch diameter welded steel pipe (e = 0.00015) at 60 lb/min. Find the friction head loss and pressure drop in 200 ft of this pipe. Assume the air to be of constant density.

2.Determine the tensile stress developed in member AB due to a load of P=500# at D. The member AB is 1/2" thick and 2" wide.

3.In the design of a simply supported skew bridge, which direction of reinforcement should be provided? explain with the help of diagram

Reference no: EM13543413

Questions Cloud

How to determine span of the subject beam which theoretical : Again assuming d=14in, determine, or at least show exactly how to determine, the portion (length) of span of the subject beam which theoretically would require no shear reinforcement.
Calculate the velocity in the constriction and the flowrate : Water flows through a 75 mm constriction in a horizontal 150 mm pipe. If the pressure in the 150 mm section is 345 kPa and that in the constriction 207 kPa, calculate the velocity in the constriction and the flowrate.
Calculate the maximum shear stress in each segment of rod : A steel rod to which three disks are attached is shown below. The rod is fixed against rotation at its left end, but free to rotate in a bearing at its right end. Each disk is 300mm in diameter.
Compute the horizontal and vertical forces on the curved : The contractor ran out of gunite mixture and finished the deep corner of a 5-m-wide swimming pool, with a quarter circle pipe of PVC pipe, . compute the horizontal and vertical forces on the curved panel AB.
Determine the tensile stress developed in member ab due : Air at 90 psia and 70 degrees F flows through a 4.5 inch diameter welded steel pipe (e = 0.00015) at 60 lb/min. Find the friction head loss and pressure drop in 200 ft of this pipe. Assume the air to be of constant density.
Determine the maximum tensile and compressive bending stress : A rectangular tube has an outside dimensions that are 2in wide and 4in deep and a wall thickness of 0.25in. The tube is acted on by a bending moment of 12,000lb-in. A.)Determine the maximum tensile and compressive bending stresses.
Explain the difference between materials considered to have : Explain the difference between materials considered to have “homogeneous” and “isotropic” material properties. Give examples of materials that are considered isotropic but not homogeneous and others that are considered homogeneous and anisotropic.
Determine the initial and final temperatures : A mass of 5 kg of saturated liquid-vapor mixture of water is contained in a piston-cylinder device at 125 kPa. Initially, 2 kg of the water is in the liquid phase and the rest is in the vapor phase
Determine the heat loss or gain during this process : A piston-cylinder device contains helium gas initially at 150 kPa, 20 degrees C, and 0.5 m^3. The helium is now compressed in a polytropic process (PV^n = constant) to 400 kPa and 140 degrees C. Determine the heat loss or gain during this process.

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Calculate factor of safety if the material does not yield

The program should use both the maximum shearing-strength criterion and the maximum-distortion-energy criterion. It should also print the values of the principal stresses and, if the material does not yield, calculate the factor of safety.

  What is the probability that the entire system is successful

Assume the components act independently and that they are equivalent in the sense that all 3 of them have an 85% success rate. Consider the random variable X as the number of components out of 3 that fail.

  Determine what is the alkalinity in mg per l as caco3

A water treatment llant and the water treatment plant removes calcium hardness (Ca2+) by precipitating (making) CaCO3(s). If, after establishing equilibrium with CaCO3(s), the dissolved Ca2+ concentration is 10 mg/L and the pH is 10.5.

  Determine the friction force exerted on the plate at a

The frame is supported in part by normal and friction forces between the wall and the plate at A. Determine the friction force exerted on the plate at A. Also determine the minimum required coefficient of friction at A for the frame to remain in e..

  State the appropriate null and alternate hypotheses

The installation of a radon abatement device is recommended in any home where the mean radon concentration is 4.0 picocuries per liter (pCi/L) or more, because it is thought that longterm exposure to sufficiently high doses of radon can increase t..

  Determine the maximum distortion energy theory of failure

At a certain location on the surface of an engineering component, the material is in a state of plane stress with principal stresses of fmax = 150 MPa and fmin = 50 MPa (both tensile). If the yield strength of the material is Y = 350 MPa

  A town is installing a new 10 main to carry drinking water

a town is installing a new 10 main to carry drinking water. the onlynbspsection remaining to be installed is a segment

  Using finite element method to find temperature of the poker

The temperature of the poker at the third points of the poker using three elements of equal length. Use the finite element method. You may use Mathcad to solve this problem. If you do, please show all work and add comments to the Mathcad solution ..

  Determine the rate of heat transfer to the stock in furnace

Cylindrical, steel bar stock (density = 7833 kg/m3, Cp = 0.465 kJ/(kg C)) of 10-cm diameter is heat-treated by drawing it at a velocity of 3 m/min through a 6-m-long furnace maintained at 900C.

  Determine the maximum fiber stress and the stress in a fiber

A simply supported beam, 2 inches wide by 4 inches high and 12 feetlong is subjected to a concentrated load of 2000 lb at a point 3 ftfrom one of the supports. Determine the maximum fiber stress and the stress in a fiber located 0.5 inches from the t..

  What fraction of the total ammonia-nitrogen is in volatile

Ammonia is a gas whose smell we detect in manure, cleaning products, and other things. The concentration of this noxious gas can be controlled by regulating the pH of the water because only the non-protonated form, NH3, is volatile.

  What is the future worth of per year of each plan at age 85

Mike and Susan hope to retire a few years early, they decided to pay closer attention to the predicted amount of retirement benefits and do some analyses on the numbers.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd