Calculate the maximum shear stress in each segment of rod

Assignment Help Civil Engineering
Reference no: EM13543415

A steel rod to which three disks are attached is shown below. The rod is fixed against rotation at its left end, but free to rotate in a bearing at its right end. Each disk is 300mm in diameter. Calculate the maximum shear stress in each segment of the rod. What is the angle of twist of section A relative to the fixed section E? Also draw a diagram for the angle of twist vs. position, showing the angle of twist for every position in the rod. (G=80Gpa)

Reference no: EM13543415

Questions Cloud

Compare those factors that determine the characteristic : Electromagnetic radiation may be treated from the classical or the quantum mechanical perspectives. Briefly compare these two viewpoints.
What will be the effect of heating the lid and jar : For a rubber component that, in its final form is to be vulcanized, should vulcanization be carried out prior or subsequent to the forming operation? Why?
How to determine span of the subject beam which theoretical : Again assuming d=14in, determine, or at least show exactly how to determine, the portion (length) of span of the subject beam which theoretically would require no shear reinforcement.
Calculate the velocity in the constriction and the flowrate : Water flows through a 75 mm constriction in a horizontal 150 mm pipe. If the pressure in the 150 mm section is 345 kPa and that in the constriction 207 kPa, calculate the velocity in the constriction and the flowrate.
Calculate the maximum shear stress in each segment of rod : A steel rod to which three disks are attached is shown below. The rod is fixed against rotation at its left end, but free to rotate in a bearing at its right end. Each disk is 300mm in diameter.
Compute the horizontal and vertical forces on the curved : The contractor ran out of gunite mixture and finished the deep corner of a 5-m-wide swimming pool, with a quarter circle pipe of PVC pipe, . compute the horizontal and vertical forces on the curved panel AB.
Determine the tensile stress developed in member ab due : Air at 90 psia and 70 degrees F flows through a 4.5 inch diameter welded steel pipe (e = 0.00015) at 60 lb/min. Find the friction head loss and pressure drop in 200 ft of this pipe. Assume the air to be of constant density.
Determine the maximum tensile and compressive bending stress : A rectangular tube has an outside dimensions that are 2in wide and 4in deep and a wall thickness of 0.25in. The tube is acted on by a bending moment of 12,000lb-in. A.)Determine the maximum tensile and compressive bending stresses.
Explain the difference between materials considered to have : Explain the difference between materials considered to have “homogeneous” and “isotropic” material properties. Give examples of materials that are considered isotropic but not homogeneous and others that are considered homogeneous and anisotropic.

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Determine the most efficient cross section with a bedslope

An open channel with a trapezoidal configuration with side batters 1V:3H is to be designed to carry 1.0m^3/s with a bedslope of 0.0065. The channel is lined with concrete with manning's n of 0.011.

  What is the net upward force exerted

the pressure inside a commercial airliner is maintained at 1.00 ATM. what is the net upward force exerted on a (1.0 m)(200 cm) cabin door if the outside pressure is 0.30 ATM?

  Freeways density and level of service

What will the freeway's density and level of service be before and after the ban? (Assume that the trucks are removed and all other traffic attributes are unchanged).

  Determine the velocity in horizontal x-y plane

A particle with a mass of 0.5 kg has a velocity of 10 m/s in the x-direction at time t = 0. Forces F1 and F2 act on the particle, and their magnitudes change with time according to the graphical force-time history shown.

  The mass of the water that is displaced by the portion

According to Archimede's principle, the buoyancy force actingon that object that is partially immersed in a fluid is equal tothe weight that is displaced by the portion of the object that issubmerged.

  What is the mass flow rate of the refrigerant in kg per s

A vapor-compression refrigeration system, using Refrigerant 134a as the working fluid, has evaporator and condenser pressure of 1.4 bar and 12 bar, respectively.

  Find what is corresponding amplitude of the acceleration

calculate the amplitude F0 of the sinusoidal excitation force that is necessary to produce a steady-state vibration with a velocity amplitude of 10 m/s at resonance. what is the corresponding amplitude of the acceleration

  What ventilation rate is needed to maintain formaldehyde

Indoor air quality is an under appreciated health hazardous. The air quality in a building can be modeled as a CSTR. Suppose that the carpet in a new office building releases formaldehyde at a rate of 10 micrograms per hour.

  At what height in the resevoirmust the water level be kept

Water at 20 Degree C is pumped at a constant rate of 9m^3/h from a large resevoir resting on the floor to the open top of a anexperimental absorption tower.

  Shear tension and bending of the fixed i-beam

To satisfy desige limitation it is necessary to determine the effect of the 2- kN tension in the cable on the shear tension and bending of the fixed I-beam.

  Radioactive waste from a clinical laboratory

A radioactive waste from a clinical laboratory contains 0.2 μCi (microcuries) of calcium-45 (45Ca) per liter. The half-life of 45Ca is 152 days.

  Determine the velocity and the volume flow rate of the steam

Steam enters a nozzle at 400oC and 800 kPa with a velocity of 10 m/s, and leaves at 300oC and 200 kPa while losing heat at a rate of 25 kW. For an inlet area 0f 800 cm2, determine the velocity and the volume flow rate of the steam at the nozzle ex..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd