Determine the required work input for this compression

Assignment Help Civil Engineering
Reference no: EM131034394

Propane and air are supplied to an internal combustion engine such that the air-fuel ratio is 16.1 when the pressure is 95 kPa and the temperature is 30°C. The compression ratio of the engine is 9.5.1. If the compression process is isentropic, determine the required work input for this compression process, in kJ/kg of mixture.

Reference no: EM131034394

Questions Cloud

Describing emotional response to a particular piece of music : Describing your emotional response to a particular piece of music, a response to a video you have watched about some world music topic or a brief essay in response to one of the readings.
Discuss any two brands from two different industries : Segmentation, targeting and positioning are interrelated activities which are important to achieving a successful Marketing Mix. Discuss any two brands from two different industries who have been successful in using these concepts in pursuit of th..
How did the song enhance or hinder the story : Did the plot make sense? Was it engaging or disjointed? Was it too long, or not long enough? Did it hold your attention? How? If you are familiar with the original source material, what do you think of the adaptation? Do not give a full plot summa..
Demonstrating your understanding of how cultural beliefs : Prepare a 3-4 page double-spaced paper demonstrating your understanding of how cultural beliefs, values, norms and practices influence communication of one of the countries or areas outside of the U.S. you choose.Include an additional full page ab..
Determine the required work input for this compression : If the compression process is isentropic, determine the required work input for this compression process, in kJ/kg of mixture.
Windows server 2008 and windows server 2012 : Most significant difference between Windows Server 2008 and Windows Server 2012?
Describe different functions/aspects of a dbms : Describe different functions/aspects of a DBMS
Describe and contrast maintenance and validation : Describe and contrast maintenance and validation techniques.
What are the 5 levels of hierarchy in a db : What are the 5 levels of hierarchy in a DB

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculating largest tolerable internal crack length

Calculate the largest tolerable internal crack length for a 7075-T651 aluminum alloy component that is loaded to a stress one-half of its yield strength without catastrophic fracture.

  What is effective vertical stress 12m below water surface

A river is 6 m deep. The riverbed material has a saturated unit weight of 19.5kN/m3. What is the effective vertical stress 12 m below the water surface

  Determine the force in member ac-fh and fg

determine the force in member AC, FH, and FG and indicate if the member is in tension or compression. List all zero force members.

  Determine the mass of the refrigerant in the tank

Determine (a) the mass of the refrigerant in the tank and (b) the amount of heat transferred. Also, show the process on a P-v diagram with respect to saturation lines.

  Determine the temperature at the final state

Also determine the temperature at the final state in part (b).

  Determine the steady-state concentration of the pollutant

A well-mixed sewage lagoon (a shallow pond) is receiving 430 m^3/d of sewage out of a sewer pipe. The lagoon has a surface area of 10 ha (hectares) and a depth of 1 m. The pollutant concentration in the raw sewage discharging into the lagoon is 18..

  Determine the final velocity of each car

The coefficient ofrestitution between each car is 0.8 . Determine the final velocityof each car, after all impacts, assuming (a) cars A and C hit Car Bat the same time, (b) car A hits car B before car C does.

  Determine the fine grains of low plasticity

Soil A is micaceous with an average grain relative density of 2.80, and has a high plasticity in its fine fraction. The ground quartz-feldspathic B is, with an average relative density of 2.65 and fine grains of low plasticity.

  What is the pulling force to be applied for one of the plate

Due to temperature change, a 1/32" hole mismatching occurred. What is the pulling force, in lbs, to be applied for one of the plates to match the two holes The plate length is 3 ft (from the left end to the hole) and its cross section is 1/8" x 1"..

  Determine the pressure variation in the flow field

A plane flow field is developed by addition of a free vortex and a uniform stream in the positive x direction. If the vortex is located a distance a from the origin, find the pressure variation in the flow field.

  How many hours should be taken an articulated wheel loader

How many hours should it take an articulated wheel loader equipped with a 4 yd3 bucket to load 3,000 yd3 of gravel from a stockpile into rail cars if the average haul distance is 300 feet one way

  Find the velocity of sphere a and wedge b immediately after

At an angle of α=30°with the vertical, a 5kg sphere is suspended on a string of length .8m with a initial velocity of 1.2m/s, it colides with wedge B. ε=.7 between the .9kg wedge and sphere

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd