Determine the maximum bending stress in the pole

Assignment Help Civil Engineering
Reference no: EM13323332

A picture of a man performing a pole vault, and the minimumradius of curvature of the pole is estimated by measurement to be4.5 m. If the pole is 40 mm in diameter and it is made of glass-reinforced plastic for which Eg=131 GPa, determine the maximum bending stress in the pole.

Reference no: EM13323332

Questions Cloud

Calculate an estimate of the friction coefficient of steel : A fellow I know wanted to know the coefficient of friction between steel and commercial carpet. The value was not in the tables of any textbook he had, so he devised an experiment.
Explain how much heat in kj is needed to warm water : How much heat (in kJ) is needed when 58.9 g of water warms and boils from 47.91 degrees C to 100 degrees C
Write a program that computes the average of five exam score : Write a program that computes the average of five exam scores. Declare and perform a compile-time initialization with five values. Use a constant to define the number of scores. Print all scores and the average value formatted with no digits to th..
Determine the maximum bending stress in the strap : An L2 steel strap having a thickness of 0.125 in. and a widthof 2 in. is bent into a circular arc of radius 600 in. Determine the maximum bending stress in the strap.
Determine the maximum bending stress in the pole : A picture of a man performing a pole vault, and the minimum radius of curvature of the pole is estimated by measurement to be4.5 m. If the pole is 40 mm in diameter and it is made of glass-reinforced plastic
What is the value displayed by system.out.println statement : What is the value displayed by the System.out.println statement?
Explain what mass of silver chloride can be produced : What mass of silver chloride can be produced from 1.27L of a 0.298M solution of silver nitrate
What is local loss coefficient of basket strainer at a point : When the pressure drops across the basket strainer by half(i.e., to 0.5 bar after the strainer)at the 100 m3/hr flow rate, itis removed for cleaning. What is the local loss coefficient of thebasket strainer at this point
Calculate radius r of neutral axis for the particular case : A circular torus of mean radius R has a thin walled circular cross-section of mean diameter d . Calculate the radius r of the neutral axis for the particular case where R=d

Reviews

Write a Review

Civil Engineering Questions & Answers

  Write matlab statement to evaluate tan write out error msgs

Assume that (t) is givenin degrees, and write the matlab statement to evaluate tan (t) aslong as the magnitude of cos(t) is greater then or equal to(10^-20). If the magnitude of cos(t) less then (10^-10,

  At the time what percentage of the principal has been paid

A company borrowes $25000 at an interest rate of a nominal 16% per year compounded quarterly. The company desires to repay the loan in 36 equal quartely payments, with the first payment starting three months from now.

  Calculate ratio of new gas flow rate to old gas flow rate

A 98% efficient ESP follows the Deutsch equation. If the gas flow rate changes and the efficiency drops to 94%, calculate the ratio of the new gas flow rate to the old gas flow rate.

  Determine what manometer reading can be expected

Is this flow laminar. What is the viscosity of the oil. For the same flow in the opposite directio, what manometer reading can be expected.

  Estimate the wet density

A sample of natural glacial till was taken from below the groundwater table. The water content was found to be 52%. Estimate the wet density,dry density,buoyant density,porosity,and void ratio. Clearly state any necessary assumptions.

  Calculate the amount of work done for the process

A container with a plunger compresses one pound mole of an ideal gas from 1 atmospheres pressure to 10 atmospheres. Calculate the amount of work done if the process is considered to be polytropic.

  Determine the maximum compression of the spring

The 30-Mg freight car A and 15-Mg freight car B are moving toward each other with the velocities VA= 20 km/h to the right and VB= 10 km/h to the left. the spring constant on car A is k= 3MN/m.

  Determine what size pipe should be use from one reservoir

The level of one reservoir is 500 ft above the level of the other, and water is flowing steadily through the pipe from one reservoir to the other.

  What the concentration in the effluent be 7 days later

A lagoon with volume 1,200 m3 has been receiving a steady flow of a conservative waste at a rate of 100 m3/day for a long enough time to assume that steady-state conditions apply. The waste entering the lagoon has a concentration of 10 mg/L.

  Estimate the et losses for the area in inches and centimeter

The discharge of the river at the basin outlet is measured at an avarage of 650 cfs. assuming that the charge in storage for the system is essentially zero, estimate the ET losses for the area in inches and centimeters for the year

  Calculate the steady-state pollutant concentration in lake

Conditions in the sewage pipe are Qs= 0.5 m^3/s, and Cs= 100mg/L. The pollutant is destroyed in the lake with a first-order rate constant of 0.2/d. The flow rate out of the lake is 5.0 m^3/s.

  Calculate soil moisture using daily precipitation and temp

Calculate soil moisture using daily (or any other scale) precipitation and temperature . Use the Richard's Equation and Darcy's law (Or any theory you like attached to soil moisture content determination ).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd