Calculate radius r of neutral axis for the particular case

Assignment Help Civil Engineering
Reference no: EM13323328

A circular torus of mean radius R has a thin walled circular cross-section of mean diameter d . Calculate the radius r of the neutral axis for the particular case where R=d

Reference no: EM13323328

Questions Cloud

Determine the maximum bending stress in the pole : A picture of a man performing a pole vault, and the minimum radius of curvature of the pole is estimated by measurement to be4.5 m. If the pole is 40 mm in diameter and it is made of glass-reinforced plastic
What is the value displayed by system.out.println statement : What is the value displayed by the System.out.println statement?
Explain what mass of silver chloride can be produced : What mass of silver chloride can be produced from 1.27L of a 0.298M solution of silver nitrate
What is local loss coefficient of basket strainer at a point : When the pressure drops across the basket strainer by half(i.e., to 0.5 bar after the strainer)at the 100 m3/hr flow rate, itis removed for cleaning. What is the local loss coefficient of thebasket strainer at this point
Calculate radius r of neutral axis for the particular case : A circular torus of mean radius R has a thin walled circular cross-section of mean diameter d . Calculate the radius r of the neutral axis for the particular case where R=d
What is the childs speed at the bottom of the slide : At a playground, a 20.2-kg child plays on a slide that drops through a height of 2.40 m. What is the child's speed at the bottom of the slide
Explain what is the [h3o+] of a buffer that consists : What is the [H3O+] of a buffer that consists of 0.154 M CH3CH2COONa and 0.645 M CH3CH2COOH. Ka of propanoic acid, CH3CH2COOH is 1.3 x 10-5.
Estimate maximum outlet velocity that system could deliver : couplings , each with a loss coefficient of k=0.15, are located every 10 m along thehose. the nozzle outlet diamter is d= 25 mm, its minor losscoefficient is k=0.02 based on outlet velocity
How much time after being thrown does the ball take to land : ball is thrown up at 13.0 m/s near the edge of a 30.0-meter high cliff. The ball lands at the bottom of the cliff. How much time after being thrown does the ball take to land

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine if its possible to pull at p without causing wheel

If the coefficient of sratic friction between the wheels at B and the ground is 0.5 determine if it is possible to pull at p=1200 lb without causing the wheels at B to slip or the front wheels of A to lift off the ground

  Conduiting with a roughness coefficient

Given an 18-in. concrete conduit with a roughness coefficient of n = 0.013, s = 0.02, and a discharge capacity of 15 cfs, what diameter pipe is required to triple the capacity?

  How deep hole would be formed as a result of the excavation

The Metrodome's inflatable roof covers 10.0 acres and its interior volume is 60.0x103 cubic feet. During construction, 40.0x103cubic yards of concrete, 11.9x103 tons of reinforcing steel, and 5.00x102 tons of structural steel were utilized.

  How to compute the horizontal distance in elevation

The slope distance between two points is 72.665 m, and the difference in elevation between the points is 1.120 m. Compute the horizontal distance.

  Determine value of force f which result in zero displacement

A rectangular steel bar shown is fixed at the right end has a thickness of 20 mm. The temperature is increased by 20C and a force F is applied as shown midway along the bar. Use the properties E=200 GPa, a=12(10^-6)/C.

  What size pipe should be used from a ground storage tank

Water flows from a ground storage tank that is 450 feet above a town's water distribution system. The pressure at the entrance of the system must be at least 75 psi and the demand is 1350 GPM.

  Determine the valve loss coefficient needed for h

Determine the valve loss coefficient needed for h=20 ft. All losses except for the flow control valve are negligible. The area of the pipe is 5 times the area of the exit nozzle.

  Estimate the expected number of trip ends at the factory

An automobile company is planning to build a 1.8 million square foot factory in Auburn. Estimate the expected number of trip ends at the factory on an average weekday.

  What are the concentrations of h2po4- and hpo42-

The total phosphate concentration (TOTPO4) in a river is 3.2 mg/L as P. The pH of the river is 7.8. What are the concentrations of H2PO4- and HPO42-

  Find the probability that more than 8 fail before 10 months

Suppose that under severe operation conditions, the lifetime, in months, of a transisitor is exponentially distributed with parameter d = 0.2. a. Find the probability that such a transistor lasts longer than 8 months.

  Plot of log-log grah of the flowrate as a funciton of h

Water flows from a large open tank through a sharp edged entrance and into a galvanized iron pipe of a length 1.5 miles and diameter of 4 inches. The water exits the pipe as a free jet at a distance

  Determine how deep will the water be on the flash boards

The pipes holding the boards were placed 10 ft apart across the dam. There were 20 pipes and each one was designed to fail under a bending moment of 1625 ft-lb how deep will the water be on the flash boards when failure occurs

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd