Determine the horizontal and vertical components of reaction

Assignment Help Civil Engineering
Reference no: EM13305649

Determine the horizontal and vertical components of reaction at the pin supports at A and B and indicate direction. Take F1 = 7 KN, F2 = 6 KN, and h = 1 m.

Reference no: EM13305649

Questions Cloud

Determine the gage pressure in the water tank a : A manometer connects a large water tank open to the atmosphere to a closed spherical tank of air. The manometer contains both oil and water. Find the gage pressure in the tank "A".
Determine the peak discharge that would result no ponds : Suppose a drainage basin has an area of 288 acres with a CN=55(Runoff Coef. of 0.30). Determine the peak discharge (in cfs) that would result from a 6.0in., 24-hr assuming there are no ponds and swampy areas.
How large must his payments be to ensure : how large must his payments be to ensure that after retirement he will be able to draw $30.000 per year from this account until he is 80?
What is fielding projected total receipts : Excess short term borrowing (if any exists)Fielding has no short term borrowing as of March 1st, 2008. assume that the interest on short term borrowing is 1% per month. What is fielding 's projected total receipts (collections) for april?
Determine the horizontal and vertical components of reaction : Determine the horizontal and vertical components of reaction at the pin supports at A and B and indicate direction. Take F1 = 7 KN, F2 = 6 KN, and h = 1 m.
Determine the energy of the ejected electrons : Molybdenum has a work function of 4.2 eV. If light of frequency 2.0 x 10^15 Hz strikes the surface of molybdenum
How long must the temperature at t2 be maintained : A block of material A is placed in closed contact with unlimited supply of material B, after 15 hours at temperature T1, it is observed that atoms of B have penetrated 0.5mm into material A.
Determine the forces in members de and ea of the truss : Determine the forces in members DC,CB and BA of the truss. State whether the members are in tension or compression. set P=7 kN. Determine the forces in members DE and EA of the truss.
What amount will be recognized as net accounts receivable : Wright has received no payments from either school as of month end. What amount will be recognized as net accounts receivable on the balance sheet as of November 30?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the load p if the total elongation of the system

A 0.25 in diameter copper rod BC is securely attached between two identical 1 in diameter steel rods (AB and CD). Find the load P if the total elongation of the system is measured to be 0.0312 in. Esteel= 29,000ksi, Ecopper=17,000ksi.

  Determine the probability of failure of the structure

If the load effect has a mean value of 88 kips and a standard deviation of 1.8 kips. If the nominal material strength is 160 kips Determine the followings 1- The probability of failure of the structure under the nominal resistance and service load..

  Find how long until the concentration of fluoride is reduced

During a snowstorm the fluoride feeder in North Bend runs out of feeder solution. The rapid mix tank is connected to a 5-km long distribution pipe. The flow rate into the rapid mix tank is 0.44m^3/sec, and the volume of the tank is 2.50 m^3.

  What is the parameter that determines the bandwidth

For a given tank circuit resonance frequency, what is the parameter that determines the bandwidth

  How much was the initial investment at an interest rate

A company that manufactures regenerative thermal oxidizers made an investment 10 years ago that is now worth $1,300,000. How much was the initial investment at an interest rate of 15% per year (a) simple interest and (b) compound interest?

  Long cantilever beam of elastic modulus

A 45 kg machine is placed at the end of a 1.6 m long cantilever beam of elastic modulus 200 x 109 N/m and cross-sectional moment of inertia 1.6 x 10-5 m4.

  Qualitative or quantitative risk assessment on the project

Conduct either a qualitative or quantitative risk assessment on this project. Identify the risk factors that you consider most important for the suspension bridge construction. How would you assess the riskiness of the project? Why?

  Determine the angle of twist

A beryllium copper wire having diameter of 1-50 mm and length of 40mm is used as a small torsion bar in an instrument. determine what angle of twist would result in the wire when it is stressed to 250 mpa.

  Determine the total resultant force

in inclined circular gate with water on one side shown in the figure. determine the total resultant force acting on the gate and the total location of center pressure.

  Determine the pressure within the tank using psf as unit

A water-filled U-tube manometer is used to measure the pressure inside a tank that contains air. The water level in the U-tube on the side that connects to the tank is 5 ft above the base of the tank.

  Write the general mass balance equation for the rinse tank

To remove the solution containing metal from a part after plating the part is commonly rinsed with water. The rinse water is contaminated with metal and must be treated before discharge. The Shiny Metal Plating Co. The plating solution contains 85..

  Estimate length of pipeline required for the friction losses

Water leaves a reservoir at 0.05 m^3/s through a 200-mm riveted steel pipeline that protrudes into the reservoir and then immediately turns a 90º bend with a local (minor) loss coefficient equal to 0.3.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd