Determine the forces in members de and ea of the truss

Assignment Help Civil Engineering
Reference no: EM13305646

Determine the forces in members DC,CB and BA of the truss. State whether the members are in tension or compression. set P=7 kN. Determine the forces in members DE and EA of the truss. State whether the members are in tension or compression. Determine the forces in members CE and BE of the truss. State whether the members are in tension or compression.

Reference no: EM13305646

Questions Cloud

What is fielding projected total receipts : Excess short term borrowing (if any exists)Fielding has no short term borrowing as of March 1st, 2008. assume that the interest on short term borrowing is 1% per month. What is fielding 's projected total receipts (collections) for april?
Determine the horizontal and vertical components of reaction : Determine the horizontal and vertical components of reaction at the pin supports at A and B and indicate direction. Take F1 = 7 KN, F2 = 6 KN, and h = 1 m.
Determine the energy of the ejected electrons : Molybdenum has a work function of 4.2 eV. If light of frequency 2.0 x 10^15 Hz strikes the surface of molybdenum
How long must the temperature at t2 be maintained : A block of material A is placed in closed contact with unlimited supply of material B, after 15 hours at temperature T1, it is observed that atoms of B have penetrated 0.5mm into material A.
Determine the forces in members de and ea of the truss : Determine the forces in members DC,CB and BA of the truss. State whether the members are in tension or compression. set P=7 kN. Determine the forces in members DE and EA of the truss.
What amount will be recognized as net accounts receivable : Wright has received no payments from either school as of month end. What amount will be recognized as net accounts receivable on the balance sheet as of November 30?
Find the expression for the maximum torque : A length L of wire carries a current i. Find the expression for the maximum torque
Find waters carbonate hardness and noncarbonated hardness : A municipality uses green energy and treats 15 × 106 gal/day of a groundwater containing the following: CO2 = 17.6 mg/L, Ca2+ = 80 mg/L, Mg2+ = 48.8 mg/L, Na+ = 23 mg/L, Alk(HCO3-) = 270 mg/L as CaCO3, SO42- = 125 mg/L, Cl- = 35 mg/L.
The social economy: finding a way between market and state : Write 900 word summary for given case study. Summary should be less than 20%, more on your personal reflection and opinion.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate temperature of the air at the exit of the nozzle

Assuming that the nozzle is well insulated and operating at steady state and that the air behaves as an ideal gas, calculate (a) the mass flow rate of air in kg/s, (b) the exit area of the nozzle in m^2,

  Direction of flow in a conical tube

A conical tube of length 8 m fixed vertically with its smaller end upwards. The velocity head and pressure head at upper ends are 1.27 m and 2.50 m respectively.

  Maximum deflection of the beam

Determine the deflection of the right end of the pointer and the maximum deflection of the beam.

  Find length and width of square basin for virus disinfection

Find the length and width of a square basin for virus disinfection of a flow of 6 MGD. You may assume a depth of 5 ft, a C•t product of 10 (mg/L) •min for 1.5-log removal, and a target free chlorine residual of 0.6 mg/L.

  What fraction of the load p is transmitted by the middle bar

The two outer bars (material A) are identical. The cross- sectional area of the middle bar (material B) is 31.544% larger than the cross- sectional area of one of the outer bars. Also, the modulus of elasticity of material A is twice that of mater..

  Define what must the drivers eye height in the van be

A civil engineering student contends that 60 mph is safe in a van because of the higher driver's eye height. If all other design inputs are standard, what must the driver's eye height in the van be for the student's claim to be valid

  Estimate the required surface area

Estimate the required surface area (A), and the diameter and the depth of the tank.

  Depth of aggregate of wheel load over soil

A 2000-lb wheel load is to be supported by aggregate over soil with a maximum bearing pressure of 1000 lb/sqft. What depth of aggregate is needed if the angle theta is 40 degrees?

  How far should a centerline extend past an object

1. What does the acronym ANSI stand for Stands for American National Standards Institute 2. What is the purpose of a titleblock The purpose of a title block is for give us enough information about the project.

  What is the maximum positive coordinate reached by particle

The position of a particle moving along an x axis is given by x = 17t2 - 5.0t3, where x is in meters and t is in seconds. (a) Determine the position, velocity, and acceleration of the particle at t = 3.0 s. x = m v = m/s a = m/s2

  What will be the mass of the rod at the end of 20 mins

A common commercial process for the production of so-called "Electronic Grade Silicon" (EGS) is the Siemens process (see figure below). EGS is of ultra-high purity, enough to be used for fabrication of microchips.

  Possible characteristic or property of sanstone

Give one possible characteristic or property of sanstone and of the quartzite that made you decide not to select it for your concrete project?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd