Find waters carbonate hardness and noncarbonated hardness

Assignment Help Civil Engineering
Reference no: EM13305643

A municipality uses green energy and treats 15 × 106 gal/day of a groundwater containing the following: CO2 = 17.6 mg/L, Ca2+ = 80 mg/L, Mg2+ = 48.8 mg/L, Na+ = 23 mg/L, Alk(HCO3-) = 270 mg/L as CaCO3, SO42- = 125 mg/L, Cl- = 35 mg/L. Determine the water's carbonate hardness, noncarbonated hardness and total hardness.

Reference no: EM13305643

Questions Cloud

How long must the temperature at t2 be maintained : A block of material A is placed in closed contact with unlimited supply of material B, after 15 hours at temperature T1, it is observed that atoms of B have penetrated 0.5mm into material A.
Determine the forces in members de and ea of the truss : Determine the forces in members DC,CB and BA of the truss. State whether the members are in tension or compression. set P=7 kN. Determine the forces in members DE and EA of the truss.
What amount will be recognized as net accounts receivable : Wright has received no payments from either school as of month end. What amount will be recognized as net accounts receivable on the balance sheet as of November 30?
Find the expression for the maximum torque : A length L of wire carries a current i. Find the expression for the maximum torque
Find waters carbonate hardness and noncarbonated hardness : A municipality uses green energy and treats 15 × 106 gal/day of a groundwater containing the following: CO2 = 17.6 mg/L, Ca2+ = 80 mg/L, Mg2+ = 48.8 mg/L, Na+ = 23 mg/L, Alk(HCO3-) = 270 mg/L as CaCO3, SO42- = 125 mg/L, Cl- = 35 mg/L.
The social economy: finding a way between market and state : Write 900 word summary for given case study. Summary should be less than 20%, more on your personal reflection and opinion.
What is the temperature gradient along the length of the bar : A copper bar 2.5 m long has a circular cross section of radius 2 cm. One end is kept at 80oC, what is the temperature gradient along the length of the bar
Determine the volumetric flow rate in each 15-cm duct : Air enters an electrical furnace at 20oC, 100 kPa, with a volumetric flow rate of 30 m3/min. The furnace delivers air at 40oC to a duct system with three branches consisting of two 15-cm-diameter ducts and a 30-cm-diameter duct.
How do the two images differ from each other : an object is at a distance d to the left of a flath screen. A converging lens with focal length f

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what is the force in the wire and beam

The 5-m long cantilever beam using a W410 x 67 standard wide flange section has a distributed load of 1200 N/m placed on it. It is also supported by a cable at B, of length 2 m with a 7 mm2 cross sectional area. What is the force in the wire

  What is the average waiting time of vehicles in the queue

A freeway has a capacity of 4500 veh/hr. A traffic accident occurs at 9AM and the freeway is closed. At 9:15 AM, the freeway is partially opened with capacity of 1500 veh/hr. Freeway is restored to full capacity 4500 veh/hr at 9:30 am.

  What torque is the engine producing at the vehicle speed

A 3400-lb car is traveling in third gear (ratio 2.5 to 1) on a level road at its top speed of 130 mi/h. The air density is 0.00206 slugs/cuft. The car has frontal area of 19.8 sqft, a drag coefficient of 0.28, a wheel radius of 12.6 inches, a driv..

  Determine the amount of energy added to the water

A mass of 200g of saturated liquid water is completely vaporized at a constant pressure of 100KPa. Determine a) the volume change b) the amount of energy added to the water

  Determine what is the elevation of the point b

Long Line: the slope distance and zenith angle measured from point a to point b were 17,685.20 ftand 93degrees 13' 46" . The instrument and reflector heights were equal. If the elevation of the point A is 1854.43 ft above the MSL Datum

  Why is the time value of money important

Why is the ‘time value of money' important for the evaluation of engineering projects? Provide at least one practical example to support your view (max 2 pages)

  Determine the normal depth in a trapezoidal channel

Determine the normal depth in a trapezoidal channel with a bottom width of 6.4 ft and side slopes of 1 vertical to 2 horizontal. The discharge is 85 ft3/s. Manning's roughness factor is 0.025 and the channel bottom slope is 0.001

  What error in pressure drop would ensue if assumptions made

horizontal pipe, and the fanning friction factor is f_F = 0.0060. what error in the pressure drop would ensue if the assumption were made that the flow was laminar, abandoning the previous value of the friction factor.

  What is the probability that the second explosion

Cities cover approximately 0.5% of the Earth's land area, which itself constitutes 29% of the total surface of the planet. What is the probability that the second explosion in part (b) occurs over a city? Assume an equally likely probability of im..

  Coefficient of friction-skidding resistance

Two passenger cars are traveling at 65 MPH on a highway moving in the same direction in the same lane. The cars are separated by 25 feet for every 10 MPH of their speed. The coefficient of friction (skidding resistance) between the tires and the r..

  Determine the power required as a function of time

A train of total mass equal to 500 Megagrams starts from rest and accelerates uniformly to a speed of 90 km/h in 50 s. After reaching this speed, the train travels with a constant velocity.

  Determine the flow rate of water through the channel

The flow rate of water flowing in a 3m wide channel is to be measured with a sharp-crested triangular weir 0.5m above the channel bottom with a notch angle of 60°. If the flow depth upstream from the weir is 1.5m

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd