Determine the amount of power that can be generated

Assignment Help Civil Engineering
Reference no: EM131034324

A river is discharging into the ocean at a rate of 400,000 m3 /s. Determine the amount of power that can be generated if the river water mixes with the ocean water reversibly. Take the salinity of the ocean to be 3.5 percent on mass basis, and assume both the river and the ocean are at 15°C.

Reference no: EM131034324

Questions Cloud

Develop a group emergency management plan : What are the functions and tasks that will be performed to fulfill the plans goals and missions - Who is in charge of specific functions and tasks? Why?
Determine the minimum power input required : Determine the minimum power input required. Also, determine the minimum height to which the brackish water must be pumped if fresh water is to be obtained by reverse osmosis using semipermeable membranes.
What strategy would you chose for an organisation : Compare and contrast BYOD, CYOD and COPE as a mobility strategy for an organisation. What strategy would you chose for an organisation with a travelling sales force of 150 people working across three (3) different time zones
Tank at constant temperature : A) What pressure would it take to compress 150. L of helium gas initially at 1.00 atm into a 2.00 L tank at constant temperature?Express your answer with the appropriate units.
Determine the amount of power that can be generated : Take the salinity of the ocean to be 3.5 percent on mass basis, and assume both the river and the ocean are at 15°C.
Do any ethical theories support the actions that you discuss : Firstly, think of the possible courses of action (or inaction) that could be taken and then consider, do any ethical theories support (or not) the actions that you discuss? Which ethical principles, doctrines or concepts apply to the actions/inacti..
High-pressure liquid chromatography : High-pressure liquid chromatography (HPLC) is a method used in chemistry and biochemistry to purify chemical substances. The pressures used in this procedure range from around 500 kilopascals (500,000 Pa) to about 60,000 kPa (60,000,000 Pa). It is of..
High-pressure liquid chromatography : High-pressure liquid chromatography (HPLC) is a method used in chemistry and biochemistry to purify chemical substances. The pressures used in this procedure range from around 500 kilopascals (500,000 Pa) to about 60,000 kPa (60,000,000 Pa).
Determine the mole fractions of the water : Fresh water is to be obtained from brackish water at 65°F with a salinity of 0.12 percent on mass basis (or TDS = 1200 ppm).

Reviews

Write a Review

Civil Engineering Questions & Answers

  What are the three main uses of a project charter

What information should be collected during a solid waste sort? What is a Pareto analysis and how does it apply to solid waste management?

  Determine what pressure must be provided at point 1

To maintain a pressure of 300kPa at point 2, what the 15 C water is flowing at 0.5 L/s, what pressure must be provided at point 1 if you neglect friction

  Determine what percent of particle are retained in clarifier

if the settling velocity of a particle is 2.8 mm/s and the overflow rate of an upflow clarifier is .56 cm/s what percent of the particles are retained in the clarifier

  Is depreciation equivalent to both investment and expense

Is depreciation equivalent to both investment and expense which have been categorized as environmental conservation cost

  Find what depth of aggregate is needed at the angle theta

A 2000-lb wheel load is to be supported by aggregate over soil with a maximum bearing pressure of 1000 lb/sqft. What depth of aggregate is needed if the angle theta is 40 degrees

  Compute ultimate design load the footing in concentric load

The groundwater table is at a great depth. Compute the ultimate design load the footing in concentric load per unit length of wall. Comment on the design. What design method would be the most appropriate?

  Determine the dry density of the soil

A small hole about 4" in diameter and 6" deep is dug into acompacted layer of a soil embankment. 2.96 lbs of motor oil withGs=0.92 is required to fill the hole.

  Determine the pressure at b in psig

Oil (specific gravity 0.752) flows through a 6" horizontal pipe under a pressure of 60 psi. Assuming no losses, what is the flow in cfs if the pressure at a 3" diameter reduction is 20 psi?

  How to design the curve of the roadway at station

An equal tangent vertical curve is to be constructed between grades of -3.0% (initial) and 1.0% (final). The PVI is at station 110+00 and elevation 420 ft. Due to a street crossing the roadway, the elevation of the roadway at station 112+00 must b..

  Determine the compositions and quantities of gas and liquid

Determine the compositions and quantities of gas and liquid when 1 lb mole of a mixture of 30 mole percent methane and 70 mole percent ethanol is brought to equilibrium at 0 F and 500 psia.

  Determine time required for the bed to complete a full cycle

The velocity of the bed is limited to a maximum value of 150mm/s to the right and 300mm/s to the left; the acceleration is successively equal to 150mm/s^2 to the right, zero 150 mm/s^2 to the left, zero, etc.

  Draw the free-body diagrams for the entire assembly or

a draw the free-body diagrams for the entire assembly or structure and each of its parts. neglect friction and the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd