Determine the actual concentration for both pollutants

Assignment Help Civil Engineering
Reference no: EM13563788

An industrial off gas steam must be treated for both particulates and SOx. The gas is at 1500 degrees F and 1.5 atm of pressure containing 80 mg/cubis meter of particulates and 25 mg/cubic meter of SOx. A two unit system is bring considered consisting of a cyclone followed by a venturi scrubber. The cyclone would remove 5% of the SOx (see below for particulates)with a pressure drop of 0.2 atm and no change in temperature.The scrubber would remove SOx with 95% removal efficiency (see below for degrees F) accompanied by a pressure drop of 0.3 atm and a temperature drop of 1000 degree F.The standard gas flow rate is 2000 scfm.Determine the emmisiion rate (kg/minute) for both particulates and SOx as well as the actual gas flow rate (acfm) emittted.Also determine the actual concentration (mg/cubic meter) for both pollutants for their emissions.

Reference no: EM13563788

Questions Cloud

Draw the bending moment diagram for the beam abcd subjected : Draw the bending moment diagram for the beam ABCD subjected to the loading obtained from 2). (The location and magnitude of the maximum bending moment must be calculated)
What are the rotational velocity in rpm and linear velocitie : One form of which consists of three equal weights joined by equal length ropes. The gaucho holds on to one weight spinning the bolas overhead. When the bolas is cast the weights cause the configuration to change
What is the uniform deterministic arrival rate : A ferryboat queuing lane holds 40 vehicles. If vehicles are processed (tolls collected) at a uniform deterministic rate of 5 vehicles per minute and processing begins when the lane reaches capacity
How much power is required to maintain straight and level : If the aircraft is flying at 8,000 ft above the ground and the engine suddenly quits, how far could the aircraft glide before reaching the ground?
Determine the actual concentration for both pollutants : An industrial off gas steam must be treated for both particulates and SOx. The gas is at 1500 degrees F and 1.5 atm of pressure containing 80 mg/cubis meter of particulates and 25 mg/cubic meter of SOx. A two unit system is bring considered consistin..
Design a cyclone that has a collection efficiency between 80 : Design a cyclone that has a collection efficiency between 80% and 85% (use parcticle size distribution given below). you must assume a dpc of 4.2 microns,an inlet gas velocity of 25 m/s and a K of 15.The unit must handle 20,000 cfm of contaminated ..
Determine the tank depth and diameter to produce an overflow : Design a circular radial-flow clarifier for a town with a projected population of 45,000. Assume that the wastewater flow is 400 L/capita-day. Size the system for a 2-hr
Compute the force fa on the roller and the x- and y-componen : Three point loads 10,000, 7500 and 9000 kN act in line 5m apart near the surface of a soil mass. Calculate the vertical stress at a depth of 4m vertically below the centre (7500kN) load.
What is the minimum required temperture of the boiler : A coal fired steam power plant is to be designed for the purpose of generating electrical power for a city with a population of 60,000 residents. Based on an order-of-magnitude analysis

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the dimensions of the pit that minimizes cost

Assume excavation costs at $100/m3, side lining costs at $50/m2, and cover cost at 25/m2. Determine the dimensions of the pit that minimize cost -If the side slope is unconstrained and -If the side slope must me less than 450

  Calculate the maximum and minimum possible dry unit weights

Find the moist unit weight of sand in lb/ft^3compacted in the field at a relative density of 60%and moisture content of 10%Given Gs=2.65. Also calculate the maximum and minimum possible dry unit weights that the sand can have.

  Determine what is the maximum normal stress in the bar

If the bar is 90 degrees F. If the bar is cooled to 40 degrees F, what is the maximum normal stress in the bar and what is the maximum shear stress alpha = 13*10^-6 /degF, E = 10*10^3 ksi

  When its axis is parallel to the direction of stream flow

A bowling ball is dropped from a boat so that it strikes the surface of a lake with a speed of 25 ft/s. Assuming the ball experiences a downward acceleration of a = 10-9v2 when in the water, determine the velocity of the ball when it strikes the bott..

  Find what is the gage pressureat the bottom of the tank

Water occupies the bottom 0.8 m of a cylindrical tank.On top of the water is 0.3 m of kerosene, which is open to the atmosphere. If the temperature is 20 degrees C, what is the gage pressureat the bottom of the tank

  Determine what is the required thickness of the plate

a spherical container with a diameter of 50 ft made of steel plate holding a gas at 50 psi. with a tensile strength of 16000. What is the required thickness of the plate

  Calculate the maximum and minimum possible dry unit weights

For a sand, the maximum and minimum possible void ratios were determined to be 0.94 and 0.33 respectfully. Find the moist unit weight of sand in lb/ft^3compacted in the field at a relative density of 60%and moisture content of 10%Given Gs=2.65

  Determine the maximum force p that can be applied without

Determine the maximum force P that can be applied without causing the two 50-kg crates to move. The coefficient of static friction between each crate and the ground is 0.25 The crates are next to each other connected

  Find actual concentration for both pollutants for emissions

An industrial off gas steam must be treated for both particulates and SOx. The gas is at 1500 degrees F and 1.5 atm of pressure containing 80 mg/cubis meter of particulates and 25 mg/cubic meter of SOx.

  Compute the displacement of the car between 2.0s and 3.8s

The position of a car traveling between two stop signs along a straight city block is given by r=[9t-(43/2)sin(2t/5)]m, where t denotes time and 0s

  Determine the decay rate constant for the die-off of anthrax

The results of his experiment are tabulated below. Assuming the experiment was conducted in a completely-mixed batch reactor, determine the decay rate constant for the die-off of anthrax.

  Determine the maximum value of the average normal stress

Knowing that each member has a 2 3 4-in. rectangular cross section and that each pin has a 12 -in. diameter, determine the maximum value of the average normal stress (a) in member BE, (b) in member CF.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd