Compute the crates velocity two seconds after p has been

Assignment Help Civil Engineering
Reference no: EM13564947

1.What is the required intersection sight distance for all 3 design vehicles for through, right and left movements for a 2 lane minor road that stops for a 5 lane, 2 way major road? The speed limit is 45 mph and this intersection is located near a major university and there are many pedestrians. The grade for the major road is 4% and 3% for the minor road.

2.A crate has a weight of 50 lb and is acted upon by a force having a variable magnitude of P=20t, where p is in pound and t is in seconds. compute the crates velocity two seconds after P has been applied. The crates initial velocity is 3 ft/s down the plane of 30 degrees, the coefficient of kinetic friction is uk=.3.

Reference no: EM13564947

Questions Cloud

Determine the dry unit weight of compaction in the field : The results of a field unit weight determination test performed by means of the sand cone method are as follows:
Calculate the drawdown at the well use r which is the : A gravel-packed well with an effective diameter of 36 in is to be constructed in an aquifer with T = 2.6 x l04 gpd/ft and S = 2.3 x 10-5. The design flow of the well is 1000 gpm.
What is the average period of time between independent : A 10-cm diameter 2000 m long pipeline connects two reservoirs open to the atmosphere. What is the discharge in the pipeline if the water surface elevation difference of the reservoirs is 50 m? Assume a smooth pipe and ? = 1.2 x 10-6 m2/s. Neglect min..
The maximum-shear-stress theory of failure : A 120-ft diameter cylindrical tank with an empty weight of 1,000,000 Ib (including the weight of the cylindrical mat foundation) is to be built. The bottom of the mat will be at a depth of 2 ft below the ground surface. This tank is to be filled with..
Compute the crates velocity two seconds after p has been : A crate has a weight of 50 lb and is acted upon by a force having a variable magnitude of P=20t, where p is in pound and t is in seconds. compute the crates velocity two seconds after P has been applied. The crates initial velocity is 3 ft/s down the..
What is the loss of energy through the jump : In a rectangular channel of 12 m width, water flows at a rate of 150 cms. At the end of the channel, there is a horizontal concrete apron of 12 m width, on which the water depth is 3 m. Will a hydraulic jump formed in the channel and why? What is the..
Find the minimum weight of the gate so that it may have : The cylindrical gate of canal headworks, having a diameter of 3m and a length of 6 m, is subjected to water pressure up to its top as shown in the Figure. The gate resisting on the concrete floor of the headworks
Determine the dimensions of the combined footing : We requiere to design combined footing which will support a load of two columns ( the two columns rest on the same footing). The columns are squared, with a width of 12" and are at a distance of 15' from centre to centre. Determine the dimensions of ..
Determine the stopping sight distance for a 5-lane : Two pipelines of equal length and diameters 15 cm and 10 cm respectively connect two reservoirs such that the pipelines are in parallel. The difference in water levels in the reservoirs is 3 m. If the friction is assume to be equal, the ratio of disc..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Estimate population for year 2011 assuming population growth

In 1800 an undeveloped country had a population of 10 million with birth and death rates of 60 and 52 per thousand per year. The situation continued until 1900, when the death rate instantaneously was reduced to 10

  Develop a preliminary design, including flow rates

Develop a preliminary design, including flow rates, pipe sizes, and pipe slopes for a trunk sewer to be laid in the development shown in the accompanying figure from 6th to 1st Streets along Peavy Avenue.

  Select an economical hss 14 by 14 for the column

A steel column has a total unbraced height of 14 ft and carries an axial LRFD load of 950 kips. The column ends are fixed. Select an economical HSS 14x14 for this column.

  Determine the aadt for the axle counts 28000 axles have

1 determine the design hourly volume for the road below recommend the k factor first.a. for a two lane highway in a

  Determine the final equilibrium temperature in k

The partition is free to move and allows conduction from one gas to the other without energy storage in the partition itself. The air and carbon dioxide each behave as ideal gases. Determine the final equilibrium temperature

  Calculate the maximum stress in the metal

A cast iron water main 14m long of 600 mm inside diameter and 30 mm wall thickness runs full of water and is supported at its ends. Calculate the maximum stress in the metal if density of cast iron is 7200 kg/m and that of water is 1000 kgm.

  Capacity of the trunk sewer

The maximum population that can be served from the new development without exceeding the capacity of the trunk sewer. Diameter, slope, and invert elevations of sewer XB.

  Is the ray bent toward the normal or away from it

According to the photon energy formula, tripling the frequencyof the radiation from a monochromatic source will change the energycontent of the individually radiated photons by what factor?

  What is the minimum settling velocity of a particles

A flow of 125,000 gallons per day enters a sedimentation basin which is 20 feet wide, 60 feet long and 12 feet deep. What is the minimum settling velocity of a particles that will be 100% removed by the basin

  Determine the diameter in meters of the exit pipes

Steam at 100 bars and 550°C enters a turbine operating in steady-state with a volumetric flow rate of 460 m^3/min. 22% of the entering mass flow exits the turbine at 10 bars, 200°C and a velocity of 20 m/s.

  Compute the allowable load on a column with fixed ends

Compute the allowable load on a column with fixed ends if it is 5.45 meters long and made from an S150 x 18.6(S6 x 12.5) beam. The material is ASTM A36 steel. Use the AISC formula.

  What will it be after consolidation is completed

The current vertical stress at a point in a saturated clay is 181 kPa. This soil is to be covered with a 2.5m thick fill that will have a unit weight of 19.3 kN/ m^3. What will be the value of the vertical

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd