Compute normal and critical depths in a concrete culvert

Assignment Help Civil Engineering
Reference no: EM13210618

compute normal and critical depths in a concrete culvert(n=0.015)with a diameter of 36in.and a bed slope of 0.002ft/ft if the design discharge is 15cfs.is the slope steep or mild?reap for S= 0.02ft/ft.

Reference no: EM13210618

Questions Cloud

What is the probability that the vehicle pulling out : what is the probability that the vehicle pulling out will get in an accident with oncoming traffic?
What type of exercise takes place in a classroom : What type of exercise takes place in a classroom setting arranged to look like an emergency operations center or in an actual emergency operations center, and involves simulation using written, telephone, and radio messaging.
When will the queue clear : where u(t) is in vehicles per minute and t is in minutes. When will the queue clear?
Explain whats the anode charge : whats the anode charge. please include the answer and why and a step process please
Compute normal and critical depths in a concrete culvert : compute normal and critical depths in a concrete culvert(n=0.015)with a diameter of 36in.and a bed slope of 0.002ft/ft if the design discharge is 15cfs.is the slope steep or mild?reap for S= 0.02ft/ft.
What type of contract would you want and why : If you were asked to perform an excavation contract competitively with limited data, what type of contract would you want and why?
Type of project communication : What type of project communication should Janet implement to discuss the status, technical issues and responsibilities on the project?
What is elastic wave tomography : what is elastic wave tomography , flat jack, push shear test in masonary?
Describe the application of geophysical techniques : Describe the application of geophysical techniques using electromagnetic induction as a tool for sustainable soil and water management of agricultural fields in the humid tropic Caribbean 300 word limit".

Reviews

Write a Review

Civil Engineering Questions & Answers

  Moles of gas in the gas sample

A gas occupise 250 ml and it's pressure is 550mm Hg @ 254C how many moles of gas are in this sample? (convert mm Hg to atm).

  Density of traffic stream in lane

Assume you are observing traffic in a single lane of a highway at a specific location. you measure the average headway and average spacing of passing vehicles as 3 seconds and 150 ft, respectively. calculate the flow, average speed, and density of..

  What length l of splice plate is needed

two strips of a plastics material are bonded together as shown. The average shearing stress in the glue must be limited to 1000 kpa. what length L of splice plate is needed if the axial load carried by the joint is 55 kN and the width (W) is 315 m..

  Four-lane freeway problem

A four-lane freeway (two lanes in each direction) is on mountainous terrain with 11-ft lanes, a 5-ft right-side shoulder, interchange spacing of one every 10 miles, and a 60-mi/h base free-flow speed.

  What is the name of the text book and author used

What is the name of the text book and author used for thr course CEE30 in the spring quarter of 2013, at University of California Irvine?

  Number of revolutions tub makes

A tub of a washing machine is rotating at 50 rad/s when the power is turned off. If it takes 15s for the tub to come to rest, determine (a) the constant angular deceleration, and (b) the total number of revolutions the tub makes.

  Seepage velocity and estimating hydraulic gradient

The dye appears 14 days later in an observation well 75 ft away from the injection point. Compute the seepage velocity and estimate the hydraulic gradient in the aquifer if the porosity of the soil is 42%.

  Sample of natural glacial-groundwater table

A sample of natural glacial till was taken from below the groundwater table. The water content was found to be 52%. Estimate the wet density, dry density, buoyant density, porosity and void ratio. Clearly state any necessary assumptions.

  Design a single angle strut connected to a gusset plate

Design a single angle strut connected to a gusset plate to carry 180k n factored load. The length of the strut between center to center intersection is 3m.

  Determine the cycle time for a single engine scraper

Determine the cycle time for a single engine scraper rated at 21 cy heaped that is used to haul material from a pit to a fill 900 ft away under severe conditions. The average haul speed will be 14 mph and the average return speed will be 20 mph.

  Absolute pressure of the carbon dioxide in the can

The circular top of a can has a radius of .0320m. the pull-tab has an area of 3.8x10^-4 m^2. The absolute pressure of the carbon dioxide in the can is 1.40x10^5Pa. find the force that these gas generates on the top of a can?

  Find the temperature stress produced

A rod of steel is 20 m long at a temperature of 200C. find the free expansion of the rod when the temperature is raised to 650C. Find the temperature stress produced

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd