Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
In the compliance calibration of an edge-cracked fracture toughness testpiece of an aluminum alloy, it was observed that a load of 100 kN produced a displacement between the loading pins of 0.3 mm when the crack length was 24.5 mm, and 0.3025 mm when the crack length was 25.5 mm. The fracture load of an identical testpiece containing a crack of length 25.0 mm was 158 kN. Calculate the critical value of the mechanical potential energy release rate Q at fracture and hence the plane strain fracture toughness Kic of the alloy. All testpieces were 25 mm thick. For the alloy, Young's modulus, E = 70 GPa and Poisson's ratio, v = 0.3.
A concentrated load of 200 kips is applied to the ground surface. What is the vertical stress increment due to the load at a point 15 ft below the ground surface at a horizontal distance of 10 ft from the line of the concentrated load
1. What is meant by the "base value" in an arithmetic gradient 2. Which two alternative comparison techniques requier equal service lives Why
At an angle of α=30°with the vertical, a 5kg sphere is suspended on a string of length .8m with a initial velocity of 1.2m/s, it colides with wedge B. ε=.7 between the .9kg wedge and sphere A.
A hi-vol clean filter weighs 18.00 g. After a 24 hour sampling period the filter is removed and weighs 18.65 g. The initial flow rate through the filter was 2.5 m3/min. When the filter was removed the flow rate through the filter was 1 m3/min. What i..
Using Fy=50ksi, select the lightest available section for the spanand loading shown. Consider moment and shear only and neglect beamweight in all calculations. The member is assumed to have fulllateral bracing.
A gravity thickener receives 33.000 Lpd of wastewater sludge and increases the solids content from 3.0% to 7.0% with 90% solids recovery. Calculate the volume of thickened sludge.
A horizontal het of water at 5 degrees celsius strikes a block and is deflected upward 30 degrees. The mass flow rate of the water is 1.75 kg/s. The mass of the block is 1.30 kg. The jet has a cross sectional area of 10 cm^2.
Using the generalized enthalpy departure chart, determine the exit velocity of the carbon dioxide
Cylindrical, steel bar stock (density = 7833 kg/m3, Cp = 0.465 kJ/(kg C)) of 10-cm diameter is heat-treated by drawing it at a velocity of 3 m/min through a 6-m-long furnace maintained at 900C.
the weight of a sample of coarse aggregate was measured under various conditions with the following results: oven-dry weight in air 1076.3 g air-dry weight in air 1083.3 gsaturated-surface-dry weight in air 1089.2 g
Consider a 1000 acre residential area with a housing density of four dwellings per acre. Evaluate the peak hourly water use requirement.
The sand particles range in diameter from 0.04 to 2.0 mm with a specific gravity of 2.65. The wastewater discharge rate is 1400 m3 /d at 20°C. Design a settling tank to remove all the metal and sand particles.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd